Recent content by AndyP

  1. A

    Hesston 6450 chrysler 225

    GraigWis Your info seems correct. A friendly parts person at local AGCO was able to check on Massey 885 swather distributor parts and was given Echlin # LX103 as part source. Also glad you were able confirm . Did order part through Amazon.ca ...Thanks for responce
  2. A

    Hesston 6450 chrysler 225

    I am needing electronic distributor pickup. I am told that this part in the industrial 225 is not the same as in the automotive 225. Is this so? Have accessed Echlin part # LX 103 availability ,so will this part work for my needs if not would anyone know the part # I am looking for? JD or...
  3. A

    Hesston 6450 windrower

    Getting one from Farmland Tractor Supply in Tangent OR , very good service .
  4. A

    JD 60 starter

    Had the same problem on one of my 60's could not get that end cap anyplace, my starter repair guy will supply me parts, he was able to find me an end cap from a different tractor make he had in his scrap pile. I had to modify it slightly for the wires to fit properly but got it to work. this...
  5. A

    JD 60 starter

  6. A

    Hesston 6450 windrower

    Broke drive axle, where can I get used one . With all of these unit still in use and many having been built, they're has to be a good place to get used parts. Can't get in my head paying $1500 for a new one . Wreckers around these parts are at half of new. Used machines are going for $2500...
  7. A

    multiple parts

    Went to our local Agland JD dealer in Northeast Alberta for an o'ring that should cost $1.50 but turned out to be over ten dollars. But they did not stock it. Was told that they could order but it only comes in packs of 5 and I would have to take all five. What gives? I used to be a...
  8. A

    JD 60 starter

    Repairing delco starter #1108950 on one of the 60's . The commutator brush holder is damaged,needs repair on brush holder assy . Where can a person get a parts breakdown and part numbers? Also need bushings, rest is good. Also would like to get parts for 4450 starter Wilson Denso #0280003292...
  9. A

    Re: 4010 diesel not starting

    Bought a 4020 a couple years ago that hadn't run in over a year. Same thing would not smoke . Flushed pump with sea foam and let stand for a day or so, came back and installed new filters and gave it a good prime ,tried it still nothing. Pulled it with other tractor and went about 50 yards and...
  10. A

    2020 gas tractor clutch adjustement

    Finally replaced clutch housing with newer style. Needed to take dual clutch apart to dry and clean oil socked clutch disks. Am now reinstalling dual clutch assembly but don't have specs on readjusting the three levers or fingers we call them . Does any one have those specs and to what...
  11. A

    9510 combine

    Want bale straw , what do I do with chopper on JD 9510 to bale straw?
  12. A

    Massey Harris 80

    Years back had a 90 with same issue. Took measurements of height and length of rib and went to a heating duck place and got a galvanized sheet of metal (thinner than the original) bent to those specs and brazed it here and there on top of the old one and it worked just fine, can't remember if...
  13. A

    JD 2020 tractor

    Turns out I had to remove flywheel housing to remove seal. Seal is supposed to be installed on crank before reinstalling housing back. Seal # is a C/R T20326T and sort of works like a bellows type of seal,sleeve on crank and spring actuated on back against crank flange and teflon against inside...
  14. A

    JD 2020 tractor

    Needing to change rear crank oil seal on eng #SNM5ITH037838T, looks like I have to remove housing #R63434 and replace it from the inside, right? Which seal can I use? What is the procedure to install over crank and which tool do I need?
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top