-
A
Hydreco 2020G5B1 specs needed, PTO pump
I dont understand what you mean by "Your question is in the list on google". Anyhow, I searched google for "Hydreco 2020G5B1" and found a downloadable pdf file from the Hydraco site for 2000 series pumps. The pdf file has a p/n decifering section that only lists the "M" series 2020 pump. Mine...- apekim
- Post #1
- Forum: Implement Alley
-
A
Hydreco 2020G5B1 specs needed, PTO pump
Looking for the specs on this hydraulic PTO pump Model 2020G5B1 Hydreco- apekim
- Thread
- Replies: 3
- Forum: Implement Alley
-
A
Can't find a standard 1-1/8 PTO shaft for 850 tractor. Ca...
My 55 850 has a 73,xxx serial number. It came from the Ford dealer with the Wagner loader and a Model 116 Pippin Backhoe. It has 520 hours on it since new. I"m trying to figure out the details on the pto pump used to power it (RPM, PSI, and volume flow per hour or minute so that I can check to... -
A
Can't find a standard 1-1/8 PTO shaft for 850 tractor. Ca...
Funny guy... I would consider the 1-3/8" splined shaft if I could find a reasonably priced 1-3/8 to 1 inch gearbox that my Hydraulic PTO Pump would mount to. -
A
Can't find a standard 1-1/8 PTO shaft for 850 tractor. Ca...
My 850 tractor has a pto adapter gearbox on it that interfaces to the standard 1-1/8" splined PTO shaft and increases the rpm speed as well as provides a 1" female spline to accept the hydraulic pump for a Pippen Digger Backhoe. All the parts websites only offer the 1-3/8" conversion PTO shaft... -
A
800 Tractor PTO speed increaser, Cone Automatic Machinery...
I'm looking for repair some repair parts for a PTO speed increaser made by Cone Automatic Machinery. Its a model A-A unit. It also offsets the pto shaft downward a bit so that a rear hydraulic pump can be used with the Pippen backhoe sump assembly. the unit came on my 55 Ford 800 tractor... -
A
Ford 850: Remove hydraulic top cover w/Pippen backhoe on it
I don't have a flat plate. It appears that my machine may have cam from the factory with a 3 pt hitch, and the Ford dealer installed the Pippen backhoe on it. I believe the pump for the 3 pt would be located where the trans meets the engine on the right hand side. All I have there is a gear box... -
A
Ford 850: Remove hydraulic top cover w/Pippen backhoe on it
Yes its the upper stubs, which the upper lift arms are typically attached for a 3 pt. I don't see any hydraulic lines coming in from the right side of the hyd top cover...it appears to have a small block-off plate where I think the lines would attach if it did have a pump. The left side cover... -
A
Ford 850: Remove hydraulic top cover w/Pippen backhoe on it
My 1955 850 Tractor has a hydraulic top cover that I would like to remove to see why my rear pto is not engaging. The stubs that normally have 3 pt lift arms attached to them have brackets on them to support the large sump for the Pippen Backhoe. If I unbolt the hydraulic top cover, will it... -
A
55 Ford 850 PTO Will Not Engage
I am not sure what to open up to check inside to determine what is wrong. When i engage the lever and let the clutch out there is a low bumping noise. It is not grinding like a transmission does, but its more of a lower tone grinding noise. Thanks for any help on this. Mike -
A
rotted fuel injector return sleeves Yanmar 3TN Diesel
Thank you very much for the information..- apekim
- Post #1
- Forum: John Deere
-
A
rotted fuel injector return sleeves Yanmar 3TN Diesel
The sleeves that have the fuel return lines are rotted and i was unsure if i should replace the entire injector with another used one or is it possible to just replace the rotted part without effecting the operation of the injector. Is there anything in particular i should know about these...- apekim
- Thread
- Replies: 4
- Forum: John Deere
-
A
rotted fuel return sleeves on injectors 3TN Yanmar Diesel
The sleeves that have the fuel return lines are rotted and i was unsure if i should replace the entire injector with another used one or is it possible to just replace the rotted part without effecting the operation of the injector. Is there anything in particular i should know about these...- apekim
- Thread
- Replies: 1
- Forum: Garden Tractors
-
A
Yanmar 3TN66 Camshaft removal with head on.Is it possible?
Thanks for the reply. I may just decide to just swap the governor assembly over without swapping the gear housing. I would only be missing the pivot mtg hole for the alternator, which is the only difference between the two. I would have to make up a bracket to attach alternator somewhere else on...- apekim
- Post #1
- Forum: John Deere
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy