(800) 853-2651
SHOP NOW

Recent content by Arkansas Red

  1. A

    o-12 mc deering

    where does a fella find replacement plugs ,titan no.1 came out, thanks
  2. A

    carburetor for FarmAll H

    Have a 6212-BD IH carburetor. Cannot find numbers in any of my carburetor books. Need a needle and seat for it. Any idea what other carburetor would match up or what this carburetor could have come off of. Thanks
  3. A

    520 ELECTRICAL

    Rebuilding a 520. All the lights are hooked up correctly on switch. Where does wire from resistor to switch go on switch. (which post) and where does fuel guage wire go to, which post? Thank You
  4. A

    JD 520

    Did they build a full mount 3 point plow for the 520? If so is that a two bottom or three bottom? Thanks for any help.
  5. A

    serial tag black dash 520

    looking for a serial tag for a black dash 520. Thanks
  6. A

    John Deere 50 in stock pulls

    There is a 50 in southern Michigan .125 overbore 10-1 comp. that eats stock g and A and Farmall H's and M for lunch. The weights where they belong the right 15.5 tires and 5000# Thru 7500# and hold on and have fun. Send the big boys home not wanting to admit what took first place.
  7. A

    John Deere 520

    Can anyone tell me if the 520 originally had a black dad or not? Any help would be appreciated
  8. A

    37 b starting

    37 b used to start 2nd turn +run great, now will not suck fuel in cyls when trying to start,choke plate closed,will blow fuel back thru carb some when turn over,compreson good,will start when pulled runs but not great tks for any help
  9. A

    1937 jd b

    is it possible for the cam gear+crankshaft gear to jump a tooth while running,tks
  10. A

    super A steering

    Is there any adjustment on the steering box on a wide Front super A
  11. A

    420 Cam Shaft

    can anyone tell me the difference between the 420 Cam shaft and the M Cam shaft, duration or lift? Will the 420 cam shaft go into an M motor?
  12. A

    International-140

    Have a 72 inch mower deck on my International 140. Blades are 25 1/2 in long 3 hole. any idea where I can find info on the mower deck and where I can buy blades. Thanks
  13. A

    Big Nut carbureator

    What would be my initial idle and load setting on a JD 51 carb? Have it on a 51 A 396 cubit inch 9.25 compression ratio. Thanks for the help.
  14. A

    tractor pulls

    Does anyone know of any tractor pulls coming up in Northern Arkansas any time soon?
  15. A

    6-2- power block

    Have a 6-2 power block, pistons and rods...no smoke, came out of a running tractor, was not smoking, top ring groove on pistons small amount of wear...trying to put a load going to Michigan coming from Arkansas this month...$850...incudes shipping...Contact Randy at 870-897-4765
See more
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top