(800) 853-2651
SHOP NOW

Recent content by Benartm80

Yesterday's Tractor Forums
  1. B

    MF 1085 hydraulic filter housing

    Thanks for the reply. Ended up buying a 6” strap wrench at the parts store and was impressed it actually worked. Had to have my buddy leaning into it while I tapped the threaded area with a hammer and she finally started to budge and eventually came off. Here is a link to the tool...
  2. B

    MF 1085 hydraulic filter housing

    Will keep trying to get that housing off. Drained the oil and it had a metallic shimmer to it. Trying to get the basic things taking care of to see if we can get the remotes back in sufficient working order.
  3. B

    MF 1085 hydraulic filter housing

    Yeah, I guess I was hoping someone would have that info or a link to it.
  4. B

    MF 1085 hydraulic filter housing

    Trying to replace the hydraulic filter and the cast 1” nut on the bottom of the housing broke off. Thinking of switching to a spin on filter housing but not sure what specs I should look for. Any recommendations?
  5. B

    1964 Ford 2000, electronic ignition dies after 30 seconds

    Thanks for the suggestions. Hooked up a timing light and it had spark all the way til it shutdown as long as the engine kept turning. Opened the fuel drain on the carb and there was a drop or two. Removed the carb and sediment bowl. Opened the carb and the bowl was decently clean but the...
  6. B

    1964 Ford 2000, electronic ignition dies after 30 seconds

    Installed the Pertronix kit on my '64 Ford 2000 several years ago with the Flamethrower coil. It has always started reliably and has been running very well up until this past fall. Cranks like normal, runs for about 30 seconds, and then dies like the key has been shut off. The sediment bowl...
  7. B

    Ford 7000 hydraulic pump o-ring

    Thanks for the links and info. Got it in the mail and had it installed in about 20 min. Lift and remotes seem to be good so far. Just so others know, here is the difference between an o-ring and a flat sealing washer Thanks again, Ben
  8. B

    Ford 7000 hydraulic pump o-ring

    Thanks! I was scratching my head looking at the parts diagram for the hydraulic pump and not finding it. Looks like I was in the wrong aisle.
  9. B

    Ford 7000 hydraulic pump o-ring

    Been using my father-in-law s 7000 for cutting hay a couple times with a 10 fella disc mower. When raising the mower up to vertical, I had hydraulic fluid spraying out the back side of the pump housing. Pulled the pump and replaced the gasket and o-ring, but on the third time raising it to go...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top