(800) 853-2651
SHOP NOW

Recent content by Bernie/MA

Yesterday's Tractor Forums
  1. B

    Where to find IH #200 blade operator manual

    Check your local highway depts for used blade edges.
  2. B

    8n is un-seized

    I used a flap wheel on a drill.
  3. B

    OK, I want to know

    I leave the twine balls in it but I blow all the chaff out and take the bales out by putting blocks of wood in to push them, out hand turning the flywheel.
  4. B

    Retiring from haying

    I built it, mounted second 2-cyl in front of feeder forks. Works good. Both engines drive original flywheel via 2 double vee belts side by side.
  5. B

    Retiring from haying

    The guy that did it for this year wants to buy all the equipment. I don"t know what I should get for it and I would appreciate some opinions. A JD 24T baler with 2 engines for power, a Hesston 110 moco selfproppelled, a pinwheel rake with a hitch to pull a Grimm ground tedder behind (turn and...
  6. B

    Today's funny

    ERTL was probably not invented 80 years ago. We had a shady area between the house and syringa bush where we played with cast iron toys and/or tin trucks that were hard to get. War was on.
  7. B

    JD 24T baler parts

    My 24T engine driven baler needs the belt tightener pulley, bearings failed. Any leads to find one would be appreciated.
  8. B

    Green Baler Parts Co

    Look up Finger Lakes Equipment in NY. They rebuild JD balers.
  9. B

    Hand clutch on TO 30

    Last year when my left hip got worse I rigged a hand clutch on all three of my Fords. On the 59 and 53 I welded a piece square tube on the arm to slide a pipe handle into. On the 47 I mounted a hinge on a block at the back of the homemade running board with a piece of 2 inch channel resting...
  10. B

    Jubilee distributer problems

    I got new cap and rotor but doesn"t fit right. It leaves brass chips under the cap. Any ideas?
  11. B

    54 NAA Steering Issue

    The top bearing doesn"t get much lube. I drilled a hole below the steering wheel to squirt in oil. If the little gasket above the tin is stiil there you can lift it up and make the hole there.
  12. B

    John Deere 420 Crawler left steering lever issue

    If you have a lift bolt a piece of chain to the top 2 holes when you get it slid out enough. It will balance. If not, next 2 down. Can"t remember. On mine didn"t have to remove sprocket to clear rock guard.
  13. B

    Made a temporary fence

    If she was not spayed I"d be more worried about males jumpinng in.
  14. B

    John Deere 420 Crawler left steering lever issue

    When you pull the fFD off be aware there are 2 bolts thru into the FD from the tranny side.
  15. B

    641 PowerMaster with Loader-Hard Steering

    Reservoir is empty. It is behind the rad on the right side below the side/hood panel. Has a clamp thing to hold the cover on. Or maybe the belt is broken.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top