(800) 853-2651
SHOP NOW

Recent content by BIG1RED9

Yesterday's Tractor Forums
  1. B

    202 oil on the brakes….again

    Hi everyone, I would have thought that rebuilding the differential would have repaired the rear end leaking onto the brakes. Nope. There are times I am at significant angles therefore more pressure against the seal? Not sure what the problem is nor how to fix it. Thank you
  2. B

    MHF 202 9” clutch question

    For clarification for future viewers. What I thought was zero free play was in-fact the throwout bearing NOT making contact with the pressure plate fingers.
  3. B

    MHF 202 9” clutch question

    Problem resolved. I mounted the pressure plate and clutch plate to the flywheel on the tractor. I used 1 25/32” as the space between the flywheel to the top of the finger. Using a digital calipers depth gauge, I placed the base of the caliper on top of the finger and slid the depth gauge down...
  4. B

    MHF 202 9” clutch question

    After finger adjustment
  5. B

    MHF 202 9” clutch question

    These pictures are with the fingers adjusted I must’ve confused the issue. The shaft rotates clockwise and returns. The biggest issue is on me. The previous set up had so much binding that the pedal felt completely different. I had clunking and clicking. So that when I rotated the shaft with...
  6. B

    MHF 202 9” clutch question

    I mounted it to the flywheel with the hub side that is slightly higher facing the throwout bearing
  7. B

    MHF 202 9” clutch question

  8. B

    MHF 202 9” clutch question

    Pictures to show hub clearance
  9. B

    MHF 202 9” clutch question

    I do not see where the spline hub of the clutch makes any contact. On one side of the clutch from the face of the hub to the wear material on the opposite side is .575” the other side is .940” The hub makes no contact that I can see and don’t think it makes a difference to direction. I want to...
  10. B

    MHF 202 9” clutch question

    The new and old throwout bearing are the same size at 1-1/2” thick. Input shaft splines have 3 1/2” exposed Both pressure plates have same height on the bench Going to mount parts and measure
  11. B

    MHF 202 9” clutch question

    The clutch shaft turns smoothly and returns. No I do not have a Massey Ferguson published manual. With the new parts installed, I have more than an inch clearance from the finger to the throwout bearing surface with the pedal depressed. After measuring the finger height of installed new pressure...
  12. B

    MHF 202 9” clutch question

    👍
  13. B

    MHF 202 9” clutch question

    From another manual
  14. B

    MHF 202 9” clutch question

    The previous 2 images are from Big Dean.
  15. B

    MHF 202 9” clutch question

See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top