(800) 853-2651
SHOP NOW

Recent content by BigC

Yesterday's Tractor Forums
  1. B

    pre oiling new engine overhaul

    You could use a preoiler but it might be overkill. As long as you used assembly lube you'll be fine. You ca always crank it over with out the spark plugs (gas) or injectors (diesel)
  2. B

    HD16 engine parts

    Did you try calling http://www.illiniparts.com/ I have used them several times
  3. B

    Rust in the fuel tank and radiator- how I got rid of it

    OK. Just in case anyone else needs a few things I have learned over the past few weeks getting my HD16 up and moving. She was plagued with rust and gunk everywhere. Time consuming but worked for me. Fuel Tank grime and rust 1. Drain old fuel and water 2. Fill it up with water. Leave room for a...
  4. B

    Bob/Ont. need your help again

    Had a similar problem with my Cat955H. Started out as little until it became a dead miss. Turned out to be water/coolant leaking into that cylinder around the injector. I know its not the same engine but it sounds like a similar problem.
  5. B

    Allis Chalmers HD16

    I had the same thoughts...I was just about ready to start tearing her apart when I thought...wonder if pressure is blowing by the injectors? Took the valve covers off and started it.....sure enough... looked like little volcanoes going off. Torqued down the injectors and all the blowby is gone...
  6. B

    Allis Chalmers HD16

    Well out of the frying pan and into the fire. Now that it is firing like it should I have a ton of alot of smoke come out the breather. Not sure what its doing now. Runs like a top...no smoke out the exhaust. Man I am getting tired of working on this motor. I may have bit off more than I wanted...
  7. B

    Allis Chalmers HD16

    Yeeee Haw. It's alive. Not without some issues but what a difference. So I worked all day on it but here is how it went. I got your pictures and it confirmed what I thought it had the inserts. Now how to get them out?? Well I got some literature from Illini Construction parts and low and behold...
  8. B

    Allis Chalmers HD16

    Yep its me from Cincinnati. I have been through this thing six ways to Sunday. I am getting a ton of white smoke that smells like unburn"t fuel. I measure how far the injector goes down and it on goes about 1/4 inch into the head and sits up high. I don"t think the bottom of the injector is even...
  9. B

    Allis Chalmers HD16

    I knew you would know Bob. I have a question does this extra insert reside below the injection sleeve. I am thinking I could pull it up through.
  10. B

    Allis Chalmers HD16

    OK somebody out there knows the answer to this. I have bee fighting with this repower of an old hd16. I put in a 25000MKII motor and it smokes like you wouldn't believe. I know what your thinking...but have 1. New pistons ad rings 2. new valves 3. been through two injection pumps. 4. new...
  11. B

    HD16 hydraulic pump seal? Bob from Ohio would know

    This message is a reply to an archived post by ACHD21A on May 18, 2009 at 15:42:04. The original subject was "Re: HD16 hydraulic pump seal? Bob from Ohio would know". Well.....not good. After searchig forever I found a seal to the tune of $150...ouch. So I put it in and it leaked just as...
  12. B

    HD16 hydraulic pump seal? Bob from Ohio would know

    Well still looking ad might have to change the seal config. If anyone has old HD16 or 21 could you check to see if you have a hydreco pump on the front of it. If so can you send me a model number. I have a partial but the tag is so destroyed I cant read it all
  13. B

    HD16 hydraulic pump seal? Bob from Ohio would know

    Unfortunately No...The Tag is destroyed
  14. B

    HD16 hydraulic pump seal? Bob from Ohio would know

    Thanks Hector...you don't have any leads on who might have that internal mechanical seal do you.Your up north aren't you?
  15. B

    HD16 hydraulic pump seal? Bob from Ohio would know

    Well the hunt begins. I called the numbers you suggested and they told me its not a Roper that controls the blade. It turns out it is a Hydreco....I've never heard of them...he said good luck they haven't made pumps like that for 30 years. He said I probably wouldn't find a direct replacement...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top