(800) 853-2651
SHOP NOW

Recent content by Bill Gellert

Yesterday's Tractor Forums
  1. B

    Minneapolis Moline Z

    Thanks
  2. B

    Minneapolis Moline Z

    Thank you
  3. B

    Minneapolis Moline Z

    Thanks so much for the information. Cleaning out the fuel system. Sediment bowl, fuel cap and carb gaskets at this point.
  4. B

    Minneapolis Moline Z

    Thank you! Out of curiosity, what does the AU stand for?
  5. B

    Minneapolis Moline Z

  6. B

    Minneapolis Moline Z

    I picked up this tractor and need to order parts from Steiner. They dont specifically show parts for a Z just like a ZA or ZAU or other. Is mine one of these?
  7. B

    Starting problem 46 JD B

    Points were burnt out bad. I had a new set and replaced. Didn't get spark. Changed out condenser with a used one. Didn't have spark. Replace coil with new and didn't have spark. Took off uSed condenser and tried without. Still no spark. Where would you go from here? Cap and rotor ar a...
  8. B

    Starting problem 46 JD B

    points were burnt out bad. I had a new set and replaced. Didin't have spark. Changed out condenser with a used one. Didn't have spark. Replace coil with new and didn't have spark. Took off uSed condenser and tried without. Still no spark. Where would you go from here? Cap and rotor ar a...
  9. B

    Starting problem 46 JD B

    It has points. I'll try the condenser. Thanks.
  10. B

    Starting problem 46 JD B

    Ignition module? Are you referring to the coil
  11. B

    Starting problem 46 JD B

    Replaced mag with delco distributor a year and a half ago.
  12. B

    Starting problem 46 JD B

    I was cutting corn stalks with a brush mower and the right plug wire hooked on a corn stalk a killed the tractor. I put it back on an can't get it started. There is no spark to either plug. All wire to coil, plugs and ignition wire look good and all connected. Haven't metered anything...
  13. B

    Where can I find old IH mold board plow parts?

    I'm still here. Bet you thought I died and went to heaven. Sorry about that. The number on the mold board is IH 03048H0. Does that help? Thanks for all your help.
  14. B

    Battery size JD B

    How big enough amp battery do I need for a 1946 JD B? I want to get as small a size as I can that will fit and still be sufficient to turn it over well. It's a 12 volt system.
  15. B

    Where can I find old IH mold board plow parts?

    Here's a picture with the share off
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top