(800) 853-2651
SHOP NOW

Recent content by Billybuck123

Yesterday's Tractor Forums
  1. B

    ballast resistor P/n?

    Front mount, Thank you
  2. B

    ballast resistor P/n?

    my 12v 8n runs crappy after 30 minutes, so I installed new coil & research the resistor, I didn't see a resistor on the tractor so I bought one, the resistor helped the coil from breaking down so fast...cant bushhog in second gear though...
  3. B

    ballast resistor P/n?

    stopped this morning & picked up a resistor it drops v from 12 to 8 but its not a ballast resistor, what is the max volt drop with a ballast resistor? thanks for any info
  4. B

    8 N oil pressure problem

    bump ?
  5. B

    52 8N Died suddenly. Won't restart

    a wire broke or fell off.
  6. B

    52 8N Died suddenly. Won't restart

    coil heating up?
  7. B

    8 N oil pressure problem

    45psi cold 35 psi hot, the machine shop re surfaced the housing and new oil pump gears...
  8. B

    8 N oil pressure problem

    Is packing the pump that important when you have already primed & ran the tractor with good oil pressure for an hr or so?, I would think eventually the grease would break down with the oil???
  9. B

    8 N oil pressure problem

  10. B

    8 N oil pressure problem

    Well I did not pack the oil pump with grease or Vaseline but I can prime thru press relief and the tractor will have oil pressure , good io press till I shut it down for a day or two..
  11. B

    8 N oil pressure problem

    After a day or 2 of not using, I lose oil pressure, just replace pickup tube because I had this problem a few months ago, I found a crack in the old one... it may be the oil I am using from what I read, but need yall's advice, I can prime it and have good pressure until I let it sit for a day. I...
  12. B

    8 N just overhauled by pro's, No oil press

    Sorry for late reply, the shop has been helpful, I just figured it out with every ones help The problem was not letting the tractor run long enough to build pressure along with priming the heck out of it had to take throttle to half throttle before I see pressure now it builds as soon as it...
  13. B

    8 N low oil presson pro rebuild

    I have good pressure after taking throttle to half position, & prime , prime , prime , Thanks to all...
  14. B

    8 N low oil presson pro rebuild

    No that is not right, First I removed line at tee going to filter, Can get pressure but its positive pressure with no return, go down line any where & do same, but when all hooked up pressure goes to zero
  15. B

    8 N low oil presson pro rebuild

See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top