(800) 853-2651
SHOP NOW

Recent content by blacksheep1875

Yesterday's Tractor Forums
  1. B

    to 35 engine change

    Hello all, I have a to-35 here that was run quite a while with no oil pressure (oil pump drive gear bad) When it was brought here it was filled with grease. Upon teardown it will need a complete rebuild. The crank, cam and 2 rods are in very poor shape and doubt very seriously if they could be...
  2. B

    Young farmer needs haying equipment advice

    Hello all and Amy welcome to the world of haymaking! We started off in haymaking about six years ago with no machinery and a six acres piece of ground.It has been tuned and tweaked alot since then. We currently do about 130 acres of grass and alfalfa hay and about 100 acres of straw. The straw...
  3. B

    WD 45 hand clutch

    Thanks for the help.....I put the handle back into position. Removed shims until .30 was met, rebushed the handle and.......It works great, good and crisp now!! Thanks for the replies.
  4. B

    WD 45 hand clutch

    The hand clutch is slipping in the WD. I adjusted it up and it just doesn"t seem to lock in like it used to. The foot clutch is fine. How was the hand clutch set up? Still have to split the tractor to replace? I have looked in several books for a clutch and it only shows the main clutch, are the...
  5. B

    help identify!!

    What is it worth?? Has a Kwik loader. no smoke. runs well.
  6. B

    help identify!!

    heres another pic.
  7. B

    help identify!!

    May be making a trade for a MH. Was told it was was a 44 special. Only numbers I can find are MFC140G35305. Any help in identifying this would be much appreciated!! Thanks. Sorry for the picture quality.....it was taken by a camera phone.
  8. B

    WD 45 Pwr rims vs bolt on rims.

    I have a WD 45 with power adjust rims. I have a bad rim. I found a fella local who has a set of rims that are center bolt type.(8 bolt) His dishes and rims are 1 piece. My question is.... what do I have to do or can I change to a regular bolt pattern? I looked my WD45 over and can see no easy...
  9. B

    te 20 housing

    Thanks for the info! Was that on the TE's only or did that apply to the TO's also?
  10. B

    te 20 housing

    Hello to all! I recently picked up a te 20 in really bad shape that is destined to be parted out. During the teardown I found the mid case (between the engine and the rear end) to be aluminum. I was a bit surprised.....my question is "Were all the te"s like this and why did they do that?"
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top