(800) 853-2651
SHOP NOW

Recent content by Bob H.

Yesterday's Tractor Forums
  1. B

    What round baler to buy

    Keith; Hello. We have a Vermeer 605F.hyd tie, open throat, which makes a tight bale up to 1500#. Cheap to buy, parts are no problem to get. As far as duel hyd. goes, I just added a duel valve, and wire the single tractor hyd. open. Works grt. Good Luck Bobmn
  2. B

    Painting my barn roof?

    Leo; This happen to us 5/6 yrs ago. A Barn painting contractor from Wi. stopped at our farm, out of the blue....and said they were doing roofs in our area. He did one 10m from us, and the next day he was doing one about 5m away from us. So to keep his crew busy, he would do ours for $500.00. He...
  3. B

    Today's job!!!

    Eldo case; Nice tractor!! I agree on the air, also. I see you have a Gantry crane. I built one a few trs ago, and would be lost without it. I'll see if I can find a pic. Thanks for the pics. Bobmn
  4. B

    Rotary mower for Farmall A ?

    KD; Just got off my A and Woods belly mount mower. They work great! I still use the hand lift (2 levers to lift} to raise and lower the deck. All belt drive and have not had to replace a belt in many yrs. Also cuts grt and doesn't leave "clumps" of grass, like our JD650 does. The trick is to run...
  5. B

    G1000 LP power steering fluid

    Joe; Thanks!! I'll pick some up tomorrow. Bob
  6. B

    G1000 LP power steering fluid

    Hi; Can anyone tell me what kind of power steering fluid this tractor used? Thanks Bobmn
  7. B

    Tractor Radio

    DBAF; I just used a cheapie from Wally w. It really boils down to the speakers. I have a Cozy Cab on my 706 Farmall and it had the spot up and behind my head. You could use larger speakers and that worked better than the two smaller speakers I had to use in my Bobcat cause of no room. I do like...
  8. B

    enough POWER to rake hay?!! And 4th of July tractor ride

    Christopher; Hi; ah yes, I know that R&C firm also!! Boy that's a deal!! I had to pay twice that! I was told that the rake is a Farmall.....maybe # 35? not sure, maybe some can tell us. I normally pull 2 rakes, a JD on the hitch, and I built a hitch on the back of that rake, to hook this rake...
  9. B

    enough POWER to rake hay?!! And 4th of July tractor ride

    Roy, Wow,200hp is really over kill!! I know a fellow that had 4 old 7520 JD's and they run single tires on. all his kids run these....as in raking hay..well they did pull TWO rakes! Bob; Did the 830 have power steering? even with that on smaller fields, kinda hard to turn sharp...
  10. B

    enough POWER to rake hay?!! And 4th of July tractor ride

    Hi to all; Well, had not run the 830 since last fall, so to ck it out, I thought I'll run it in the field here first. If it quits, I won't be on the road. Wife drove our 70 Standard gas, neighbor had his 8n and one CA allis. I pulled our 32'' trailer with a 48 Gibson, 1953 40, and a 44 LA. A 5...
  11. B

    G1000 LP steering and (bailing hay)

    Hi Guys; Well, we used our propane 1000 to bale hay this week. Was working great.....the hyd. are smooth for wrapping twine. Ok great......The next day I start the tractor and I hardly touched the steering wheel ,and the frt wheels cycled back and forth, etc etc!! Any ideas before I find the...
  12. B

    70 gas standard flywheel specs

    Hello; First, thanks to both of you for taking the time to answer. I should have said up front......I do have the books, but we are redoing the office in the shop, and every thing in stored in box's all over the place! All that was wrong, was the ring gear was bad. Some one did put a new starter...
  13. B

    70 gas standard flywheel specs

    Hi;I just put a good flywheel ring gear on the flywheel.....I have the shaft cleaned up, and the marks lined up. Should a person use red lock tite, or a sleeve type lock tight? Also, should the bolts be tighten to 250 ft #'s ? And, I see the handle for the pto is almost on the platform...can...
  14. B

    John Deere D

    Lester; I also have a 44 D. Last April, I met the guys from Robert's Carb, and got the drill bits for cleaning out the passages. It's RUST that's the problem. Also shows the one passage that gets missed. Have the video also. Now, to fine the time to get the carb done!! Good luck, Bobmn
  15. B

    Ride for coffee today

    Thanks Guys; Well, we are in Little Swan Mn......which is 20m south of Hibbing Mn. We started doing this Memorial Day ride some yrs ago. And yes, the coffee is good! Bob
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top