(800) 853-2651
SHOP NOW

Recent content by Boisdarc1

Yesterday's Tractor Forums
  1. B

    54 super c how to adjust govner

    Hey 560dennis. Can you explain how much added braising material you tacked on to the part that attaches to the shaft ( the part with 2 repairs)? (Re at .300 sid radius?)
  2. B

    51 farmall super c surging

    The springs on that arm? No binding that i can see…
  3. B

    51 farmall super c surging

    Yes. I played with that one too.
  4. B

    51 farmall super c surging

    Ill check this linkage springs…. Havent really touched those in this quest
  5. B

    51 farmall super c surging

    Yes. I cleaned and rebuilt carb. New jets ect. Surging not really the problem after i replaced distributor…. Just having a lack of range in throttle and would i would gather 25-30 % less rpm without a reliable tach…
  6. B

    51 farmall super c surging

    Thanks jim, Where is the speed change lever?
  7. B

    51 farmall super c surging

    Grandpa love Why would a new buffer spring bend? Screwed in too far? Ill keep messing with the linkage but between the linkage and the buffer i feel like have been all over the place…
  8. B

    51 farmall super c surging

    Ok. Follow up…. Running rough and surging. Tried to rebuild distributor but had trouble with a screw and broke the housing with an easyout. Got new distributor from this site and installed. Runs much smoother but still no throttle depth and rpm still seem low. So i Screwed in buffer...
  9. B

    51 farmall super c surging

    I did adjust bumper spring(new) in and out. No engine improvements ( no change ) in or out…..
  10. B

    51 farmall super c surging

    The stuck in 3/4 turnout out to be the ball in the shift stick rusted and frozen. Banged out with hammer and all is fine . Still surging a bit. Might try a distibutor rebuild?
  11. B

    51 farmall super c surging

    Thanks grandpa love -i messed with the linkage and pushout out about 3/16 forward from specs. Runs much better. Applied impact hammer (without bit) to try and shake vibrate into movement but still stuck in n/3/4. Pin ins in there frozen, but ill try and get out after the weekend...
  12. B

    51 farmall super c surging

    Yes brownie450. I could move in 3/4th gear. Just wont shift to others. O way to free from shifter opening if i remove pin? I remember pulling off top and it was a b_$@%# to get gears aligned…
  13. B

    51 farmall super c surging

    Oh, i forgot. New governor assembly with throw out bearings….
  14. B

    51 farmall super c surging

    Good mornining. I have a 51 super c that is surging. It sat for 15 years. But i have managed to get started. She needs some love. I have: rebuilt zenith carb New points and condenser wires coil and plugs New battery and cables Rebuilt governor with shaft and bushings ( fixed worn...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top