(800) 853-2651
SHOP NOW

Recent content by brandond

Yesterday's Tractor Forums
  1. kcm.MN

    2022.11.18 "Extra" Pic

    Puzzle: https://jigex.com/HowqP
  2. jon f mn

    Picking corn and bear damage

    Picked a few loads of ear corn this weekend with the picker I just got. Went fairly well with only a couple issues to work out. After that it worked good. I did find a couple spots where the bears had been eating. No dens this year tho. Just 5 acres left to combine and this year...
  3. H

    Rear engine seal

    I recently bought a TE20 Ferguson tractor, it's got the Z120 engine. No way to get the engine serial number, as everything is painted over and not legible. Tractor serial number is 27945. I need to split the tractor, as it looks like the rear engine seal needs replaced. Can anyone tell me...
  4. S

    3000 - Troubleshooting power steering (right turn diffic

    I have a 1970 Ford 3000 I purchased a few months ago. Upon purchasing I replaced the filter in the power steering pump and replaced the steering shaft seal, as fluid was almost pouring out of the column. I only went down to the shaft seal and didn't remove valve assembly or anything else. When I...
  5. A

    Planter monitor harness 37 pin - Precision Planting vs D

    I purchased a planter and the seller kept his Precision Planting 20/20 monitor. Is the 37 pin connector from this planter that connected to his Precision Planting monitor going to work on the monitors I all ready have? I have Kinze 1000 and 2000 monitors which are Dickeyjohn and a John Deere...
  6. B

    Ford 960 Front weight box

    In search of a front weight box for a Ford 960 or even just the dimensions of one, need a bit more weight up front when picking up my brush hog. Any help is much appreciated.
  7. D

    bumper hinge

    This message is a reply to an archived post by Maxwell 99 on January 04, 2014 at 06:38:24. The original subject was Re: bumper hinge. The flat iron on mine go up and or I mean vertical I have seen one like it somewhere I don't have a ferguson but just wanted it to be complete.
  8. J

    8N Overheating

    Have mowed grass and bush-hogged pastures nearly weekly with my early 8N (front-mount, 12v, EI) this summer, without difficulty or issues. Yesterday, about 1 1/2 hours into a 2 hour job, with temps in the mid-80's (not as hot as some days), it began spewing steam from the radiator cap overflow...
  9. Z

    1850 Hydraulics

    How to visually inspect hydraulic thermal relief valve. Thanks
  10. D

    John Deere 6400 electrical issue to in tank pump

    I have a 1995 John Deere 6400 with cab. 2 years ago I had to replace the fuel pump in the tank. The other day I go out to feed the cows and the tractor would start and immediately die. I then noticed when I turned the ignition on I couldnt hear the pump in the tank running. I figured the pump...
  11. L

    JD 830 pony motor oil leak

    My 830 pony motor leaks oil. Oil comes out from under the pony motor near the starter. I'm assuming this is the crank shaft seal? Anybody have any other ideas? Any ideas, short of replacing the seal, on how I might remedy this problem?
  12. C

    Getting into hay? Learning from those that know #128512;

    Hi all, If you were getting into hay, on a small scale, mainly to cover costs of equipment usage and ideally put a couple bucks in the pocket - what pull behind equipment would you run? Sickle mower? Mower/conditioner? Hay rake? Tedder? Rotary windrow rake? Etc? Any suggestions on...
  13. C

    Don,, dealer

    cnt
  14. K

    Oliver Potato Planter

    I have what appears to be a Superior/Oliver Potato Planter, but can not find any printed information such as Operators and Parts Manuals. Would anyone have any information to share?
  15. M

    Happy aniversary today !

    100 years ago today John Deere bought the Waterloo gas engine co. Thus launching JD into the tractor business.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top