(800) 853-2651
SHOP NOW

Recent content by brumik

Yesterday's Tractor Forums
  1. B

    Super C Cam Gear installation

    OH - i guess, play it safe and pull the engine. Went from fairly simple project - i thought ---- then turned major.
  2. B

    Super C Cam Gear installation

    Thanks for your advice. i've actually already have oil pan off. So next is the pump and other gadgets. I'll mess around a little tonight and see how it goes.
  3. B

    Super C Cam Gear installation

    Thanks to everyone -all great advice / direction. Bruce
  4. B

    Super C Cam Gear installation

    Thanks Hal - Do you know how i pull the cam?
  5. B

    Super C Cam Gear installation

    Yes, it is interface fit. i have heated the gear to about 200+ degrees. it goes on fairly nice, but the shaft moves back far enough where it bottoms out before it's all the way on. The shaft and gear are very clean, no burrs at all. And, as Gene mentioned, i hope i didn't knock the plug out...
  6. B

    Super C Cam Gear installation

    Oh Oh, is there any way to tell if i knocked the plug out? If knocked out, we're talking engine removal to put back? Doesn't it sound unusual that the shaft slides in and out about 3/8" ? I did clean the Shaft and gear - no knicks. it goes on nice with very slightest press fit, but the shaft...
  7. B

    Super C Cam Gear installation

    I put new Cam Gear on, but can't get it on all the way. There's too much back slop on the shaft, and as I'm rubber hammering the gear on, it bottoms out on the engine face with about 3/8" to go yet. The shaft floats back as I'm hitting the gear. I have heated the gear for easier fit. So, either...
  8. B

    Farmall super c - cam gear governor gear timing que...

    Thanks - i will time the governor - i just wasn't sure how important it was.
  9. B

    Farmall super c - cam gear governor gear timing que...

    What's funny rusty is - i've been told both ---- that it must be timed, and that no, the C doesn't need to be timed. I'm just pretty sure that the governor gear wasn't meshed with the punch mark, and it ran nice. But i'm not 100% certain about the mark. I just hate to do it one way, and have to...
  10. B

    Farmall super c - cam gear governor gear timing que...

    Thanks - but, are you saying if it runs off distributor it doesn't need to be timed? Bruce
  11. B

    Farmall super c - cam gear governor gear timing que...

    I replaced a bad Cam Gear on my super c. I've got the punch marks meshed up on the crank and cam gears. Do i need to also do the same with the governor gear? I actually don"t think the governor gear was in mesh with tick mars when i took it apart. I think it was about one third way around the...
  12. B

    Installing cam gear on Super C -Timing question

    Thanks Hal and Andrew!!
  13. B

    Installing cam gear on Super C -Timing question

    OK - I"ve got the tractor split, and finally have removed the Cam Gear. It had stripped teeth. Just dawned on me. How do i make sure the timing is correct between the Cam Shaft and Crank Shaft - and i guess the Distributor Gear may have to be timed as well. Any feedback is appreciated. Is there...
  14. B

    Super C - installing oil pan - bolt torque?

    Wayne, BK, Toro, Thanks - I'll be light and snug -- and keep an eye for leaks. Pan does seam pretty straight, so should be OK. Bruce
  15. B

    Super C - installing oil pan - bolt torque?

    I"m putting my oil pan back on and wonder what a good bolt torque is when tightening. Can someone give a good range? Thanks, Bruce
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top