(800) 853-2651
SHOP NOW

Recent content by Buckeye Wes

Yesterday's Tractor Forums
  1. B

    300 U TA clutch

    I just got my ta housing bolted back up to the rear end. I ended up replacing all bearings and updated to a sprag. TA rebuild wasn't that bad to rebuild for someone who has never done it before. I had help from guys on here. (Thanks). Now I ended up pulling ta pressure plate apart and...
  2. B

    TA ramp wear

    That?s kinda how I was thinking, but now I?m second guessing myself because when I called a couple tractor supply guys to check on bearing prices they said I don?t need to replace the bearings unless I?m sure they are bad. Years ago i was taught if you pull a bearing off you should replace...
  3. B

    TA ramp wear

    Is the wear on ramp bad enough to worry about. What would be options, replace?, repair?
  4. B

    300 U TA

    Thanks I'll give another try tomorrow.
  5. B

    300 U TA

    Is there a method to get the TA ramp off. I have the planetary gear section pulled out and the 4 bolts holding it out, but can't seem to get the ramp out. Also tried to press the shaft out of the rear of the TA, the one that engages into planetary gears on one side and into transmission on the...
  6. B

    Input shaft

    Yes I need one. Also as I pulled out the TA it came apart and the 8 roller bearings fell out. Is it normal for the TA to split apart when pulling out by hand.
  7. B

    Input shaft

    I'm pretty sure I found my noise. I believe if I would of tried to engage pto it would not of spun, there is no teeth left in pressure plate, not sure how I missed that when I removed it. The Ipto shaft splines that connect to pressure plate show more wear than I want. $300 is a lot for that...
  8. B

    Input shaft

    Will the throw out bearing be putting pressure on pressure plate fingers all the time? When I hold pressure plate up to ipto splines to check how bad it?s wore, it?s about a 1/4 to 3/8 away from engaging teeth. The pp fingers are hitting throw out bearing long before splines engage. That doesn?t...
  9. B

    Input shaft

    Will the throw out bearing be putting pressure on pressure plate fingers all the time? When I hold pressure plate up to ipto splines to check how bad it?s wore, it?s about a 1/4 to 3/8 away from engaging teeth. The pp fingers are hitting throw out bearing long before splines engage. That...
  10. B

    Input shaft

    No but splines are showing some wear. Throw out bearing shot but it grinds when siting still clutch in or out makes no difference. It looks like the input shaft has or is rubbing on the back of the crank. Not sure if that's possible but shaft nose looks like it rubbed a shiny circle on back...
  11. B

    Input shaft

    I was mowing on my 300 u this summer and get a loud metal on metal grinding noise. I thought I tore up a bearing on input shaft or pto. Started it briefly in barn to try and pin point noise. I went ahead and split tractor yesterday thinking issue would be easily found. My question is is it...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top