(800) 853-2651
SHOP NOW

Recent content by Buddy Terry

Yesterday's Tractor Forums
  1. B

    Readjusting front wheels on Allis C

    Thanks Dick for the illustration of the worm gear, and pawl also information on end play
  2. B

    Readjusting front wheels on Allis C

    Thanks Aaron for the information, that is what I thought, but wanted to be sure
  3. B

    Readjusting front wheels on Allis C

    Good morning all of you Allis men, what is the best way to readjust the narrow front end on Allis C, after removing the steering gear box, and how much end play should the steering shaft how on a Ross gear box. Thanks Guys
  4. B

    Engine Sleeve SM 4 1/8, good used piston

    I have not removed the piston as of now, the sleeve has some grooves running vertical on it, so assuming the piston will have some damage also. The tractor ran great, it had developed a skip , changed plugs, points, condenser cap wires rotary button, rebuilt carb, Ran a compression test,# 1...
  5. B

    Engine Sleeve SM 4 1/8, good used piston

    Can anyone tell me where I can find a good used 4-1/8 piston. And does anyone know if you can just buy one set of rings for it, or do you guys recommend to re ring the complete engine while it is down. This tractor sits most of the time, only use it maybe 2 or 3 time's a year
  6. B

    C steering segment gear and pinion gear

    Thanks Dick L. for the drawing break down, easier too see parts with it enlarged. But do you know how tight the segment gear nut on the steering shaft should be? Like I said earlier, the shop manual say's as tight as you can get it, but that locks it down. I guess I will look at something else...
  7. B

    C steering segment gear and pinion gear

    I'm in need of some expert advice on my C narrow front end, was wobbling so bad that you looked like you had been at the bar. On a more serious note, Had almost a full round of free play in steering wheel, adjust steering gear box, no results, found steering arm on bolster had lots of free play...
  8. B

    Engine Sleeve SM 4 1/8

    Thanks Janicholson for the information
  9. B

    Engine Sleeve SM 4 1/8

    Thanks rustred, I will have too see if my NAPA store can get one.
  10. B

    Engine Sleeve SM 4 1/8

    Thanks D.Slater for that information
  11. B

    Engine Sleeve SM 4 1/8

    Where would be the best place too look for just one sleeve for my SM 4 1/8th id. Thanks in advance
  12. B

    SM Head Bolt Torque

    Can one of you fine gentleman tell me what the head bolt torque is for a Super M. Thanks in advance
  13. B

    bobcat skidsteer loader

    Thanks AJ, I will check these suggestions out.
  14. B

    bobcat skidsteer loader

    Have a friend that has a 553 skid steer loader say's when traveling straight that it will try to steer to the right by itself. Also the bucket and boom will lower by itself jacking the tractor all the way up when not running over a period of time. Or can someone tell me where to find a...
  15. B

    480 E backhoe right outrigger comes up slow.

    Does your left side outrigger work properly, and does the cylinder housing have a block mounted on it with a steel line coming from the bottom of the barrel. If so that will be a lock valve for blocking the fluid to hold the cylinder in one direction until it is called for the valve to shift and...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top