(800) 853-2651
SHOP NOW

Recent content by Buff3922

Yesterday's Tractor Forums
  1. B

    Rear Main Seal Leak after rebuild of 850

    Hey Larry. I m having the same issue you seemed to have had. It s leaking in the same spot but only after the oil system is pressurized. It doesn t leak when the engine is turned off. What did you end up finding out about yours?
  2. B

    Ford 841 power master oil pressure and leak

    Bern, Sean, used red. You guys have no clue how much your responses and help are appreciated. Sean, it s not leaking at the bell housing. It s leaking right where the engine butts up to the bell housing. It s coming from the rear end of the engine. Again. Thank all of you for your suggestions...
  3. B

    Ford 841 power master oil pressure and leak

    Yes it s coming out rather quickly and only when the system is pressurized. When tractor is off it doesn t come out. Not over filled. I did not have the block worked on. I checked the seal and it s fine and lined correctly. It’s coming out at the bottom right where you split the tractor from...
  4. B

    Ford 841 power master oil pressure and leak

    I have a 841 Powermaster. I sent the head in and had it completely rebuilt. I took pistons out cleaned the cylinder walls and soaked all pistons in diesel for 5 months due to one having stuck rings. All cleaned up nicely. Had the crank machined and got new oversized bearing installed. Re...
  5. B

    New Holland 3010s

    New Holland 3010s set up for two years. Just got it up and running. Changed hydraulic fluid and filter. My rear lift arms are up and won't go down down. What should I do next. I'm not familiar with these tractors. It's a 3cyl diesel. Made in 2001.
  6. B

    Ferguson TO30

    thanks for the advise. I figured as much. I now have a 1953 Ferguson tractor for sale. Good condition.
  7. B

    Water in Oil

    are you sure its water and not gas? Do you turn on the gas to the carb after each use?
  8. B

    Ferguson TO30

    I need my tractor to be able to lift a heavier load (1500 lbs). Is there a way to up grade to a larger hydraulic pump to allow this to happen? I need to pick up large round bales of hay on the rear end.
  9. B

    52 Ferguson to30 hydraulic pump

    Good job! Thanks. That's a big help. I really appreciate it.
  10. B

    52 Ferguson to30 hydraulic pump

    I appreciate it guys. I guess my problem now is that I can't find one with that rod for sale. NOWHERE. no one I've talked to seems to know if it'll work without it.
  11. B

    52 Ferguson to30 hydraulic pump

    I'm rebuilding my hydraulic pump. I noticed the control valve has a long rod attached to it. The new one does not have this. Will it work without the rod?
  12. B

    9n hydraulics won't lower - looking for help

    JMOR on the diagram for the control valve you posted, I'm wondering if the wiggler/oscillator is a must. I ordered a rebuild kit for my Ferguson and it doesn't come with that part. Just the valve. Thanks for your help in advance
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top