(800) 853-2651
SHOP NOW

Recent content by BUSHNELLMAN

Yesterday's Tractor Forums
  1. B

    obviously I am not savvy enough to post this message in the right order please forgive me for...

    obviously I am not savvy enough to post this message in the right order please forgive me for hilarious post
  2. B

    6/6 with everything disconnect from the cross over arm, first of all I am able to move the rod...

    6/6 with everything disconnect from the cross over arm, first of all I am able to move the rod freely, and I would say I am able to rotate that cross over arm maybe about 60 degrees from left to right, what I am saying is this too much slop? I am stuck right now with feeling I am writing to much...
  3. B

    5/6 I seen in the repair manual that the with the throttle lever pushed full open that the...

    5/6 I seen in the repair manual that the with the throttle lever pushed full open that the governor spring should extend to 3 1/16th I have not verified that but I understand what they are asking and intend to look at that when I get time to open it up.
  4. B

    4/6 Last year I took the governor off and found that I had a lot of rust on the shaft that the...

    4/6 Last year I took the governor off and found that I had a lot of rust on the shaft that the thrust bushing rides on ,so I cleaned that up and made sure everything was free, also the spring and weights looked okay
  5. B

    3/6 With the engine off, and the carb linkage off I move the throttle lever forward and i can...

    3/6 With the engine off, and the carb linkage off I move the throttle lever forward and i can see the throttle arm ( on the left side of the engine where I have taken off the carb linkage) move approximately a full half of an inch so it seems without the resistance of the carb linkage the...
  6. B

    2/6I can feel the spring tension on the throttle lever as I try to increase speed, so I know the...

    2/6I can feel the spring tension on the throttle lever as I try to increase speed, so I know the spring isn't broken as I manually rev the tractor with the linkage disconnected I believe I see the throttle arm move to back to slow the engine down so I believe my weights are still intact
  7. B

    2.5/6 I took off throttle linkage and I can pull the lever on the governor(on the right side)...

    2.5/6 I took off throttle linkage and I can pull the lever on the governor(on the right side) back and no change I have checked the carb linkage adjustment and it seems fine
  8. B

    1/6 saw your name on some searches i did for the problem I am having. 39' AC WC I have no speed...

    1/6 saw your name on some searches i did for the problem I am having. 39' AC WC I have no speed control, I mean I start the tractor up -runs great, I push the throttle to increase rpms and nothing stays at idle, I cannot get past idle unless I go over and manually force the throttle lever to...
  9. B

    Scored a gem today

    Can I ask what GOTO findley is, I'll google it otherwise thanks!
  10. B

    sawmill

    it is a 48 inch insert tooth blade
  11. B

    sawmill

    I have had it running as fast as the WC will go,well full throttle, which brings to mind another question, but first , I see no wobble in the blade, does this mean I could actually go faster, if I had a different power source? The question that came to mind...is there any way to change the...
  12. B

    sawmill

    I responded to wrong post! This post was edited by BUSHNELLMAN on 08/31/2021 at 01:20 pm.
  13. B

    sawmill

    I'm in need of some operating info on an old sawmill I just refurbished. Is this the place to ask or where should go to ask the multitude of questions I have? Such as how do I know what HP and what RPM the mill should run at. Right now I am using the same setup my grandpa used, running the mill...
  14. B

    sawmill

    I'm in need of some operating info on an old sawmill I just refurbished. Is this the place to ask or where should go to ask the multitude of questions I have? Such as how do I know what HP and what RPM the mill should run at. Right now I am using the same setup my grandpa used, running the mill...
  15. B

    stand alone power unit

    how big of mill are you running? are you cutting hardwood?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top