(800) 853-2651
SHOP NOW

Recent content by c.perkins

Yesterday's Tractor Forums
  1. C

    adjusting farmall 300 governor

    what is the correct way to set the throttle shaft connecting rod on a farmall 300 governor
  2. C

    adjusting farmall 300 governor

    what is the correct way to set the throttle shaft connecting rod on a farmall 300 governor
  3. C

    M hitch

    Can a hitch for a M be made to fit a 300 with out quick hitch
  4. C

    Farmall Super H help

    Carb fuel line fitting. you can get them from www.external_link.com Part # IHS972 about $20
  5. C

    Galvinized wheels on farmall 300

    Did the 300"s come with Galvinized wheels. If so was it front and rear or just rear?
  6. C

    IH governor

    I have a Farmall 300 that the governor seems to react slow. Iam going to check for internal wear and free play in the linkage. but I want to know if I should install a Stock replacement spring or is there some thing better if so where can I get one
  7. C

    300 r/c steering

    I am using a old Fisher plow pump on my 300. I mounted it to the Gen bracket and made a mount for a mini Alt on the other side of the motor. works great and fits good. pump is about the same size as the Gen. just had to play around with pulley sizes to get good power stering at idle.
  8. C

    hard to start kohler

    commands should have 10w30 oil in them if you use 30 oil m0st of the time you will get noise. is it a valve cover mounted fuel pump if so check your oil for gas alot of times they leak into the valve cover. it sounds like a fuel pump. they are not servicable parts just replacement parts. good luck
  9. C

    ram 250 ideas

    with a 3 speed auto being toped out at 65 it must 4.10 gears in it. A freind of mines 90 is like that. my 91 with 5 speed will get about 70-75 with 3.73. but I do see the need for a two speed. i am not sure about the brake pedal but I have seen many trucks in the bone yards like that must be a...
  10. C

    Organic vs Ceramic

    What clutch is better for pulling. I always perfer organic for trucks, used for work not talking about pulling trucks. but am open minded when it comes to pulling parts. being used in a Farmall 300. Most of the pulls a go to are dead weight pulls but I plan on some sled pulls next season.
  11. C

    My Farmall H Tires

    What is the problem with the 12.4-38
  12. C

    Sand Blasting Cabinets

    all the others are right about the vac. system and cleaning the part of oil and grease. the best advice I can add is to make sure to get the clear plastic cover that goes over the window. It helps save the window from being damaged by the sand.
  13. C

    Going price for suit case weights?

    Out here in MA they get about $1 - $1.50 a pound
  14. C

    Farmall 300 clutch

    Need a new clutch full disc or 4 pad which is better for pulling/work ?
  15. C

    Wayne wood chipper

    not to bad of a price. but the drum bearins should be checked. also I cant remember if the wayne had the set screws on the knife lands to adjust them or if it was Mitts and Merills that had them. any way if it does hope they are able to move they can be hard to free up. 318 is a great engine for...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top