-
C
Getting a 1219 going
Went and got me a 5 ton puller and that gear came off no problem lol. Got the rest apart and swapped the seal so now time to get her back together. Does anyone know if i need to put sealant between each one of these shims between the main gear case and the roller gear case? Im thinking probly...- caboshvt
- Post #24
- Forum: John Deere
-
C
Getting a 1219 going
Havent got the coupler off yet but judging by the rest of the mower im sure shes doinked, how did you fix yours? Looking like ill need to rent a bigger puller too, just stripped the treads on mine today trying to get that gear. Also do you think i need to actually pull that shaft out of the...- caboshvt
- Post #21
- Forum: John Deere
-
C
Getting a 1219 going
I was careful to keep things in order. I found a good parts diagram online that shows the 2 bearings and c clip rings all as one assembly basically. Got the rear roll drive shaft out and i just have to get a good puller to get the end bearing off to swap the seals and that should be good...- caboshvt
- Post #17
- Forum: John Deere
-
C
Getting a 1219 going
Alrighty got the right oil and filled her up. But its all back out now because these 2 seals are shot. Anyone know the torques for the gear bolts on both these shafts? Also the belt pulley bolt? And im sure this information would all be in the manual so does anyone know a good place i could...- caboshvt
- Post #15
- Forum: John Deere
-
C
Getting a 1219 going
Alright got the belts, blades, and teeth replaced and shes all greased up, just needs some fresh oil now. What oil should i use in the gear box and wobble box? 80w90 im assuming?- caboshvt
- Post #13
- Forum: John Deere
-
C
Getting a 1219 going
Oh nice that tool looks handy i’ll def take a look at them. Any chance you know what rivets i will need to use to attach the new blades?- caboshvt
- Post #7
- Forum: John Deere
-
C
Getting a 1219 going
Thanks for the reply. That must be the problem i had with the belt, i need the A- number not the P- that i was trying. For the teeth though i guess im calling them the wrong thing, i meant the blades on the sickle bar not the finger things on the pickup reel- caboshvt
- Post #3
- Forum: John Deere
-
C
Getting a 1219 going
Just picked up an early model 1219 mower for $800 and it needs a few things before it gets cutting. First i need the knife drive belt. I found its supposed to be part number E46844. I ordered one online but it was too tight to get on, even with the adjustment loosened all the way. The number...- caboshvt
- Thread
- Replies: 23
- Forum: John Deere
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy