(800) 853-2651
SHOP NOW

Recent content by Casenut

Yesterday's Tractor Forums
  1. C

    ATTN CASENUT-2050A bucket level phots

    The other is my pivot is on the lift cylinder pin and not the bucket cylinder pivot.
  2. C

    ATTN CASENUT-2050A bucket level phots

    The big difference is your linkage is on the right side as my loader the pivot that is there is on the left side.
  3. C

    ATTN CASENUT-2050A bucket level phots

    Nice looking tractor. That is completely different than the one I have. Thanks for sharing though.
  4. C

    2050 loader

    Thanks I would really like to see what it looks like
  5. C

    2050 loader

    I have a 2500a tractor with a 2050 loader on the left side where the lift cylinder pins on is a bracket that swivels on the same pin. I believe it is for the bucket level indicator. If it is I do not have the rest of the linkage. I have a book for the loader but does not show this.
  6. C

    2500 industrial hydraulics

    I have a 2500a industrial with a 2050 loader. The loader seems weak and somewhat slow. I have replaced the filters and all the fluid. I am suspecting the pump may be worn. Any other suggestions? The only pump I cam find is a 544708r92 and mine is a 544707r93 do they interchange?
  7. C

    Oil pressure relief valve

    Thanks guys. I did figure it out. The spring does go inside the cup and the other end of the cup goes against the plug. The plug I had in there was pitted and not sealing. Put a good plug in problem solved.
  8. C

    Oil pressure relief valve

    I am rebuilding a c200 gas engine for a 2500a same as a 574. The question I have is one the oil pressure relief valve. I don't remember how it goes together. I know the spring is below the plunger but does the spring go inside the plunger cup or does the plunger go in with the cup side against...
  9. C

    2500a steering

    Thanks for the reply Jim. I have been on that site already. There is not an illustration for the kingpins. The 574 uses a spindle. I may have to go to a IH dealer to see what is available.
  10. C

    2500a steering

    I recently bought a 2500a which has the solid cast front axle. I need to replace the kingpins and bushings. Can anyone supply me with part numbers and a good supplier.
  11. C

    Baraboo Show. Thanks

    I could not agree more I had the time of my life there and all my dreams came true being able to complete my restoration and it was a added bonus to be able to park my tractor next to your B, Don. Sure was alot of people comparing the differences between your B and my C. I thought that was...
  12. C

    Baraboo

    I will be there. I am there every year. Bringing a 1929 C. Been looking forward to this show for a long time. Last convention in Baraboo was 1996
  13. C

    pieces and parts

    Finishing a restoration on a C Case. Would like to know what I can use for the insulator under the fuel tank and need a fuel cap gasket where can I find one or what can I make one from.
  14. C

    Case C info

    I am finishing up a restore on a 1929 C. It has the rear scraper brackets and scrapers but am missing the angle iron that runs across the back and ties the brackets together. I am looking for the correct measurements of this angle iron (width, thickness and length) This part was ussually removed...
  15. C

    Very Interesting C

    Very interesting. I could have used a set up like that this weekend. I was plowing with my L and got stuck a couple of times. What do plan to do with the tractor? Looks like I could use a couple of parts for my C from it.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top