(800) 853-2651
SHOP NOW

Recent content by Casey Keele

Yesterday's Tractor Forums
  1. C

    8N loses oil pressure

    Not that I'm an expert here or even close. I changed the oil pressure releif valve and spring on my 9n and it went from 20lbs to 40 lbs and holds.
  2. C

    Linkage problem on lift ?

    I am having the same thing. Narrowed it down to the spring that goes from the cylinder to the "knee" on the fork linkage. Finding one that works like the original is the thing. I haven't found one that works as well. I got one from the local hardware store and it has a little to much tension...
  3. C

    1939 Ford 9N Hyd. Question

    Zane, Did as you suggested and it is the spring that is not strong enough to pull back on the knee of the forks. Running into a problem finding a spring to replace it. I did get one at the hardware store but it has too much tension. Apparently these must not go bad often because i have searched...
  4. C

    ford 9n hydraulics stopped working

    HCooke I still have the old one is not broken just too weak to work right. I emailed him but he has old ones too that are 60 or 70 years old. I might run into the same problem with one of these. Is there a way to put tension back on the old spring to make it work?
  5. C

    ford 9n hydraulics stopped working

    This message is a reply to an archived post by Hobo,NC on March 27, 2012 at 18:28:03. The original subject was "Re: ford 9n hydraulics stopped working". Speaking of that spring that goes from the hydraulic cylinder to the linkeage. I need a new one and no one carries it as a ford part. I found...
  6. C

    1939 Ford 9N Hyd. Question

    Ended up being the spring that goes from the hydrualic cylinder to the control fork. i put in a new spring and the lift started working. goes up and down just fine....has a little jerky motion to it but will lift 500 lbs with no problem and no noises.
  7. C

    1939 Ford 9N Hyd. Question

    Thanks for the info Zane. I did put gaskets on right and I took it apart and rechecked thinking either the gaskets were blocking holes or something was blocking the tube running up to the cylinder. Everything was good. I did a good clean and flush of the sump area and soaked and cleaned the pump...
  8. C

    1939 Ford 9N Hyd. Question

    Thanks Jason I'll giver a shot. Appreciate it I have tried everything else I could think of.
  9. C

    1939 Ford 9N Hyd. Question

    anyone also got a trick for hooking the control valve up between the forks. it might just be me and my gotilla hands but that is a real pain doing it through the inspection holes. I got it after 45 minutes of grunting and cursing but was thinking i am doing something wrong.
  10. C

    1939 Ford 9N Hyd. Question

    Hcooke I rebuilt the whole pump. New cam blocks, valves, springs, basically everything is new except the pump housing. I put in a new piston in the hydraulic cylinder. the cylinder had no scoring on the inside. I changed the old three steel ring out to the NAA 2 o-ring style. Soundguy if by t...
  11. C

    1939 Ford 9N Hyd. Question

    Has anyone on here heard of bleeding air out of the hydraulic pump. I have just rebuilt my pump and cylinder including a new piston and rings. before I started the hydraulics worked but were making noise and would not hold up an implement with pto off. now after rebuild hydraulics dont work at...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top