(800) 853-2651
SHOP NOW

Recent content by Catman977

Yesterday's Tractor Forums
  1. C

    Caterpillar 977 Bucket Pin Removal

    Yep I didn't grease my bucket pins enough.. My son came with a VEVOR press that had a hollow center, he welded a 1 1/2" course threaded rod into the threaded hole in the pin. He then sled the Vevor Beast press, onto the rod then ran a large nut to hold it on. This press is air operated, and...
  2. C

    Caterpillar 977 Bucket Pin Removal

    Hi Everyone: I have a problem with my 977K Bucket Pin removals. I have tried everything to press from the inside out on both pins, used Heat, Dry ice and a 50ton press jig, on the inside pushing out, also had a Jig set up, for the outside using the pin threads for...
  3. C

    Rocker oil feed tube

    Hi everyone. I'am having trouble pulling the feed tube, to replace the seal on the end. It will turn completely but wont pull out. This is the tube that feeds the Rocker arm. is there anything, I could pour down to maybe soften the seal? Thanks Max
  4. C

    no oil pressure

    I have a fresh complete rebuild on my 800 Ford Tractor 172 cu in Engine. I have oil flow out the port to the guage, but no pressure to the guage. I installed a new oil pump while the engine was being assembled. What creates pressure with the pump? Thanks Max Harmon Sr
  5. C

    Flywheel Timming Marks

    Hi everyone: I have a Ford 821C with a fresh rebuild engine. I can't seem to locate the timming marks on the face of the Flywheel. Anyone have this problem? Thanks Max
  6. C

    No oil to Rockers

    Thanks for that spec sheet it really helps. I had the machine shop pre assemble the block befor I got it home and finished up the rest. I pulled the side cover that is over the push rods and that rocker supply tube is in the center. I can see the seal flush with the bottom. should it be...
  7. C

    Rocker oil delivery tube.

    Thanks I did find that out and started turning the engine with out the coil wire and did get pressure. One more quuestion though . The oil pressure port is behind the Hydraulic Pump. Whats the best way to replace that line without kinking it? Thankls Max
  8. C

    No oil to Rockers

    Oil delivery tube not oiling on a Fresh rebuild 800 Ford Engine. ?? Any one know if this tubes termination in the block with the Pan dropped can be seen? Can this tube be extracted from the engine by pulling it up from the top of the head for inspection of the end and seal?
  9. C

    Rocker oil delivery tube.

    Oil delivery tube not oiling on a Fresh rebuild 800 Ford Engine. ?? Any one know if this tubes termination in the block with the Pan dropped can be seen? Can this tube be extracted from the engine by pulling it up from the top of the head for inspection of the end and seal?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top