(800) 853-2651
SHOP NOW

Recent content by CatmanFS

Yesterday's Tractor Forums
  1. C

    Case 300 and woods RM500-2 finish mower

    Got everything hooked up, works pretty good. Top link is a little too long, but I have enough room to tighten it down and should be fine. Either way I'm going to drill 1 or 2 more holes so it's more adjustable. Left the extra space on the lower arms, might drill another hole or 2 on those as...
  2. C

    Case 300 and woods RM500-2 finish mower

    Maybe something more like this. I didn't finish it, at that point I had decided to just lengthen the arms and such. Still, might be helpful for someone
  3. C

    Case 300 and woods RM500-2 finish mower

    This was the longer quick hitch I planned out. Sizes and measurements are proportional, and I was designing it based only off stock steel sizes and shapes I already have laying around. I was in the process of figuring out how to set up stiffeners that would box it out in the back. Since it's...
  4. C

    Case 300 and woods RM500-2 finish mower

    I did indeed, but the extra 4-5" it would give me is just not enough to keep the wheels from hitting. I was going to build one myself that would be longer, but the extra work and steel required isn't worth it or needed. I had even drafted up a 3d model of a quick hitch that would be long enough...
  5. C

    Case 300 and woods RM500-2 finish mower

    So I made some longer arms for the woods RM500-2. I couldn't find any other examples of someone using this mower on this tractor and with the front wheels so this is how I've approached this so far. Using two 3" x 0.5" x 24" flat bar mild steel. Original distance between front and back...
  6. C

    Case 300 and woods RM500-2 finish mower

    I picked up another 3"x1/2"x2' piece of flat bar. I got one last week thinking 2' would be enough to get both sides, but I didn't notice the ones on the mower are already 6-8" and I would have only gotten another 2" each side. So I'll post up some pics of cutting/drilling those and seeing how...
  7. C

    Case sickle bar mower

    Is there a reason it is made of wood? Was it used like that originally? Just curious.
  8. C

    visit

    Those shoulder straps are stylin!
  9. C

    Case 300 and woods RM500-2 finish mower

    A relative gave us a woods RM500-2 finishing mower a while back and am trying to get it fit up to the case 311 I think it is(unsure), the problem is the woods has 2 wheels in the front and it hits the back tires of the tractor, and or the eagle lift arms don't reach back far enough so it will...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top