(800) 853-2651
SHOP NOW

Recent content by cdhunter

Yesterday's Tractor Forums
  1. C

    MF30 Instant reverse tractor Sudden failed to move

    I am following your post with interest, since I have a MF50E Powershuttle tractor I am going to have to split to replace a leaking seal on the input shaft of the transmission and I am an old goy too. Best of luck with the repair on your MF30! I used to own a MF30B and it was a sweet tractor.
  2. C

    Hyster YE-40 Used Parts

    Thank you to both for the information. This post was edited by cdhunter on 12/27/2023 at 09:18 am.
  3. C

    Hyster YE-40 Used Parts

    I recently acquired a late 50s Hyster YE-40 forklift and I am looking for a source for used parts. Currently I am looking for the brake pedal arm and the inching pedal arm. Any recommendations would be appreciated. I am located in Preist River, ID Thank you and Happy New Year! CDHunter
  4. C

    Help Identify Massey Industrial Model

    Based on the photos it looks like it could be a 30B.
  5. C

    TO20 Rear Drag Link Ends

    The drag link ends I ordered fit without any modifications. The only down side is the lack of a zerk fitting, which I will remedy. The part number is Sparex: S.40167
  6. C

    TO20 Rear Drag Link Ends

    I appreciate the suggestions, but I think I found a source for the correct drag link. If they fit properly, I will post the part number. Thanks, Chris
  7. C

    TO20 Rear Drag Link Ends

    Hello - I have a 48 TO20 and I am having difficulty finding the correct rear drag link ends. The replacement set I ordered, from (2) different sources, appear to have too long of stud (the one that engages the steering box pitman arm). The stud length on the OEM drag link end is 5/8" and the...
  8. C

    Rubber between gas tank and mounting bracket?

    I used baler belting, cut to the correct width, from Tractor Supply on my TO-20 and my Case VAC.
  9. C

    Tractor Show Idaho Panhandle

    I am in Priest River. My tractors are not pretty either. 1948 Ferguson TO-20 1949 Case VA 1951 Case VAC 1983 John Deere 650 MFWD 1986 Massey Ferguson 50E MFWD
  10. C

    Tractor Show Idaho Panhandle

    I hope this is the right place to post this... If it is not, please accept my apologies. Since I now reside in Northern Idaho, I am hoping some of you fine folks can tell me if there are any tractor shows in my area. I used to go to the tractor shows in Lynden, WA which were very enjoyable...
  11. C

    51 VAC Shop Manual Recommendation

    An email has been sent. Thanks for the replies.
  12. C

    51 VAC Shop Manual Recommendation

    I recently acquired a 1951 Case VAC and I would like to get a quality shop manual prior to starting the restoration. Any recommendations? I have purchased repro shop manuals for my Massey Fergusons in the past and they left a lot to be desired. Thanks, Chris
  13. C

    Continental engine dependability

    What a coincidence....My shop in N. Idaho is currently going up. What size shop are you going with? Here is a pic of the progress.
  14. C

    Agco parts books

    I can browse the parts manuals for the Industrial models as a guest on the North American AGCO site. You may want to try this link... https://na.apb.agcocorp.com/p/masseyferguson/651282/l/106?
  15. C

    Adjusting the brakes on a MF-50 Industrial

    I am glad I could help. Please post a pic of your tractor, if you don't mind. I always appreciate seeing pics of Massey Ferguson industrial tractors.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top