(800) 853-2651
SHOP NOW

Recent content by Centaur Nut

Yesterday's Tractor Forums
  1. C

    826 Hydro with no reverse

    By my book I'm coming out the right way. When I remove the cap I see the tip of the valve with a snap ring holding a washer & spring on it. I can push it in & it springs back out so far but won't come any farther.
  2. C

    826 Hydro with no reverse

    I have swapped the forward & reverse valves, with no change.
  3. C

    826 Hydro with no reverse

    Owen, I can push the valve in. It's springloaded,but moves and feels smooth. The spring pushes it back. I just can't pull it out of the valve body like my I&T book says I should. The servos are moving like they should as compared to my other Hydros. I made a plexiglass plate so I could see them...
  4. C

    826 Hydro with no reverse

    Hey Guys. I've posted about this tractor before. Early spring we were cutting hay with it & suddenly the clutch (foot&inch valve) quit working, it went forward no matter where you put the selector lever, & selector lever kept creeping up as you traveled across the field. After much headbanging &...
  5. C

    Pete23 Owen Aalund, Many thanks!

    I found my 826 Hydro problem! My Father-in-law, who ran this tractor for many years, was old time farmer and a firm believer in "blue glue". Whenever he worked it he would just wipe the parts off & smear another coat of silicone on it. After running your tests I pulled the servo and found the...
  6. C

    HELP! 826 Hydro tranny trouble!

    With the lines capped how should it act? Will I have any range control or will it just be wide open or stopped? If it is the pump servo can it be reached without breaking the tractor in half? The service manual I have mentions a clogged orifice in the pump servo as a possible cause, but not all...
  7. C

    HELP! 826 Hydro tranny trouble!

    Pete, do you mean the 2 lines coming up to the selector valve from inside the transmission, behind the left battery, and which end do I cap, transmission or selector?
  8. C

    HELP! 826 Hydro tranny trouble!

    I was cutting hay & having fun when suddenly the clutch(foot&inch valve) quit working. I had to pull the range selector to neutral to stop. I then discovered I have no reverse, but the tractor shudders when you put the selector in reverse, and when you move the selector into forward range the...
  9. C

    826 Hydro wants to go it's own way!

    If I am going forward and depress the clutch and come to a full stop, place the shift lever in reverse and release the clutch the tractor will move forward 5 to 6 feet before stopping and going int reverse, and the same thing happens when shifting from reverse to forward. If I shift to neutral...
  10. C

    826 Hydro wants to go it's own way!

    This is more than normal delay. If you stop in forward & shift to reverse without releasing the clutch the tractor will move forward 5 to 6 feet before stopping and going into reverse. Hy-Tran is good, filters have been changed. Can the shuttle valve be cleaned?
  11. C

    826 Hydro wants to go it's own way!

    Fellows, I"ve inherited an IH 826 Hydro that runs & works sweet, but when you shift from forward to reverse or vice-versa it wants to keep going the way it was going for a short distance before changing directions. I"ve noticed that if I stop in neutral and let the clutch pedal come all the way...
  12. C

    Anyone need a D282 block?

    Dead center of Alabama. About 25 miles south of Birmingham.
  13. C

    Anyone need a D282 block?

    No, all I have is a block, camshaft, bad crank, 5 good rods and 6 pistons
  14. C

    Anyone need a Farmall D282 block?

    I'm cleaning out my Father-in-laws shop, and have a buildable block I hate to see scrapped. If someone wants it email me at [email protected]. I'm in central Alabama.
  15. C

    Anyone need a D282 block?

    I'm cleaning out my deceased Father-in-laws workshop, and have a buildable block if anyone needs it. I hate to just scrap it! If interested email me at [email protected]. I'm in central Alabama.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top