(800) 853-2651
SHOP NOW

Recent content by cghoerichs

Yesterday's Tractor Forums
  1. C

    Delmhorst FX-2000 - 1986 Baler Sensor Install 567 JD

    No, my plan is to integrate the moisture sensor into baling without preservative. I have researched them and am still "considering" one. The brand would be Harvestec when I finally pull the trigger. They use the Delmhorst moisture sensor as part of their system. My reason for installing at...
  2. C

    Delmhorst FX-2000 - 1986 Baler Sensor Install 567 JD

    I couldn't find any detailed information online about installing the Delmhorst FX-2000 moisture sensor 1986 into a John Deere large round baler in this case a JD 567 so I made a video to help the next guy who tries it. http://www.youtube.com/watch?v=n2mm7ylnwNg Delmhorst FX 2000 Moisture Sensor...
  3. C

    4440 3pt draft

    Yep, that was it. Set it to Min and all is good. Thanks for the help.
  4. C

    4440 3pt draft

    I just purchased a 4440 and put a snowblower onto the 3pt. The 3pt lever has to be basically at 0 for the 3pt to lift. In the "all the way up" position it brings the 3pt all the way up in a snap but it basically has two positions. All the way up and all the way down. I assume there is a way...
  5. C

    1850 D

    Missed you by a day. I traded it in...
  6. C

    1850 D

    You make a good point there. We do a small amount of square baling and we alternated between a IH 1066 and the 1850. The 1850 was much easier to run and a lot cheaper on the fuel than the 1066 with the square baler. Don't get me wrong. I really liked running the 1850 for hay being able to go...
  7. C

    1850 D

    I'm getting a JD 4440. Its [i:47e0ea327d]newer[/i:47e0ea327d] has more HP for field work and nope, I don't know if something will go wrong with it. I really depend on my tractor for baling both custom and my own and the 1850 let me down on the clutch and then the fork during baling and the...
  8. C

    1850 D

    Hmmm. Thanks. Guess taking the cab off is the hard part. I was told that the engine had to come out to get to the center fork.
  9. C

    1850 D

    I have an 1850 diesel that I've had for about 10 years. I broke a fork in the transmission. It has less than 10 hours on an engine overhaul from this past winter, new rubber on the rear and a new clutch. It was a working tractor used for hay baling so it's not like it is parade ready or...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top