(800) 853-2651
SHOP NOW

Recent content by dbrown8978

Yesterday's Tractor Forums
  1. D

    How to engage the Belt Pulley on Case VAI

    I have a Case VAI. When I pull the lever at the back the main pto shaft engages, but the belt pulley will not spin. Is there another way to engage this pulley or how is it supposed to work? I can't find anything online and ive lost my operator manual. I have an exploded parts book and my only...
  2. D

    Looking for power steering rams to fit my Jubilee

    Looking for the power steering rams and lines if possible that I could use on my Jubilee that im converting over.
  3. D

    Jubilee/NAA Center Case relief valve questions

    I found a spare unknown lift cylinder in my dad's parts bin so I swapped that in for giggles and now I have lift and can pick up a bush hog. Something must be borked in the other one. For now I think it's finally solved, ill work it more this summer. Thanks for all your help guys.
  4. D

    Jubilee/NAA Center Case relief valve questions

    That was the point of the experiment, to see if I could force it either into the ram itself, or have it open the safety valve, and it did neither, except slowly ooze out around my (apparantly poor) block attempt and down the side of the case like melted ice cream on to my hand directly below...
  5. D

    Jubilee/NAA Center Case relief valve questions

    I suppose as you guys say fluid shouldn't be making it down there to begin with whether i've attempted to block it off or not. So ill have to open the valve area again and see if the unloading one is still stuck on an old grime ridge or how freely it moves by hand. There could also be a plugged...
  6. D

    Jubilee/NAA Center Case relief valve questions

    That's a better terminology for it but yest it's more of a garden washer/faucet washer.
  7. D

    Jubilee/NAA Center Case relief valve questions

    I assume you're talking about the flat o ring that pops into the nickel sized hole in the side of the cylinder housing? If so I initially tried it with a brand new one and still no lift, it wasn't until I blocked it off with a plastic cap and then stuck my hand in that I discovered it was still...
  8. D

    Jubilee/NAA Center Case relief valve questions

    As far as I can reasonably crank it without breaking something. It has to stick out some tiny bit for the acorn nut to grab but also not a million miles, so I have a small crescent wrench that fits perfect in the slot tabs and I use that to wind it in until it snugs as hard as I dare. As far...
  9. D

    Jubilee/NAA Center Case relief valve questions

    At this point im not ruling out a defective back pressure valve still so my plan is to delete the old one and have the port be tapped and put in an elbow and custom blow off while putting a bung in the casing for the old acorn nut. I read that the system needs 2000 psi to work but what pressure...
  10. D

    Jubilee/NAA Center Case relief valve questions

    Why isnt my bypass/unloader valve moving then when I move the handle up and down for the control valve? Or does it have to be positioned manually during the repair of it? Maybe I did something wrong and it's stuck in one spot and I dont realize it? This post was edited by ChairDancer on...
  11. D

    Jubilee/NAA Center Case relief valve questions

    So im not sure what this means, but I got desperate and just stuck my hand in the cavity and felt for oil while a partner cranked the engine over (with no spark plugs) and despite my plug on the port ive discovered that fluid is pouring out of that port around the rubber button seat and my cap...
  12. D

    Jubilee/NAA Center Case relief valve questions

    So I literally just plugged off the back pressure port on the cylinder itself that goes to the acorn nut and reinstalled the cover and still no lift.
  13. D

    Jubilee/NAA Center Case relief valve questions

    Done that already. I tried to punch out the other smaller plug but it wouldnt budge so I assumed it was pressed in instead.
  14. D

    Jubilee/NAA Center Case relief valve questions

    I have a Jubilee/NAA with some hydraulic issues im trying to fix. Already rebuilt the piston pump, cleaned the lines, freed up the lift cylinder and new gaskets, freed up the back pressure valve and still have no lift even though when I pull the plug off the pump oil comes pouring out. I took...
  15. D

    Looking for Jubilee Live PTO parts

    Well then that's my second question, will it still operate without the accumulator and with the outlet blocked off going to it if it WERE there? Or does it slam in and out of engagement without the softening or feathering as you put it that I surmise it would provide?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top