(800) 853-2651
SHOP NOW

Recent content by chargerguy

Yesterday's Tractor Forums
  1. C

    Slip Clutch adjustment on shredder

    Vermeer used sameslip clutch onall their baler until they changed to waltershied driveling make a wrench out of 1/2 plate that's all they did. Early ones had a eared nut that could be beat on to adjust but the hub was cast and would brbreak.Yours is later clutch. I would advise loosening it up...
  2. C

    1975 White 2-105 pulling sleeves help

    My dad told used to tell 2hen he worked at for CD dealer they would use a co2 fire extinguisher to rapidly cool the sleeves. It took 2 guys one would hold a heavy rag on the bottom the other would shoot the cylinder full then while wearing a leather glove reach in and make a fist and jerk...
  3. C

    Hesston 5800 round baler

    All round balers must have everything turning to work right. First thought is the hay wet some models will wrap and look things up. Are the roller knives all in place on the drive rollers? Many used balers had them removed less to hang up in dry hay. If a chain is jumping the gear it is either...
  4. C

    1000 rpm Round Baler Opinions

    Any vermeer that has the aluminum gear box case can be reversed to change from 540 to 1000 also is really tuff gear box timken bearings gears separate from shaft. We sold more for other uses than for balers. Not sure of whether or not your baler is a painted vermeer or hesston all vermeer...
  5. C

    Vermeer 605J

    Shaggy bale none side is where the bottom roller is still in contact with the bale while the gate is opening. The bale is stopping but the roller is still turning. Either shut off PLO or open gate faster( higher rpm =greater hydraulic flow=faster gate. Double check belt route I have related and...
  6. C

    2-105 broken hub

    Is the axle size the same also?
  7. C

    2-105 broken hub

    I don't think they are the same. Has a really weird bolt pattern good price though will keep in mind thanks for reply
  8. C

    JD non stop round baler??

    Vermeer has been working on one since the 70s first saw one in 77 i think. They had problems with the stringing. Plus it was a big heavy baler. Back then they did less structural engineering more if it bends/breaks make it heavier bigger. JD had a tendency to copy others innovations then...
  9. C

    2-105 broken hub

    Anyone know of a good place to obtain a rear hubfor a 2-105? The right rear broke a unbolt and shear the key out of it. It is a single wheel hub. Only provision for deals are eyebolts on rim. Don't really need deals to bale hay with any way. I'm located in southern Illinois but I drive all over...
  10. C

    white 2-70 over under-no under drive

    Sprag clutch in backwards it is one way only clutch or it is slipping bad sorry no easy fix from what I understand.
  11. C

    1975 White 2-105

    Loosen rear cab mounts remove front cab mounts unbolt cab from console then jack up front of cab. There are 2 bolts on each side at the bottom under floor mat and brackets at top on each side you may want to unbolt gearshift boot to prevent it from tearing. I think I removed the front bolts on...
  12. C

    Looking to upgrade baler

    The vermeer rebel series and later either have or can have not wrap added. The one we have suffered a lot of abuse from a former farm manager. Had to replace chains but without oil any chain will not last other than that its been great monitor and twin tie bale ramp just add hay and rpm. Now is...
  13. C

    Equipment you flogged to death and didn't die ?

    Minneapolis Molina G1000 dad workedat Molina dealer mom went there to see new tractor said where is it while standing up on a transmission housing dad told her she was standing on it. That was1970 I believe one clutch 2 hydraulicpumps and tires still in use today
  14. C

    New holland knotter new knife makes problems

    Ok got this thing partly figured out thanks for all replies. And thanks to FB macafoos in benton il a former new Holland dealer. They came up with a book not same number but has same knitter. Left side twine finger out of adjustment. And the new knives were wrong be all that is available. Wife...
  15. C

    New owner of 847 auto tie good or bad?

    847 new Holland i assume? The old chain new Holland would bale wet or dry hay beats the leaves off alfalfa if dry. Will work until chain breaks then it will be expensive to repair but at that price you can scrap it and come out
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top