(800) 853-2651
SHOP NOW

Recent content by CharlesG

Yesterday's Tractor Forums
  1. C

    Model M

    After looking at my service manual I need to be looking at the service manuals for the MT and 40. If no press is needed then I think I can get the job done.
  2. C

    Model M

    I was looking in the service manual and it appears that I need a press. Can putting a new seal in be done without one? You saw a picture of my shop.
  3. C

    Model M

    Thanks!
  4. C

    Model M

    M-MAN, I checked the TOM level and it’s low again. How hard is it to pull the pump and do I have to pull the radiator too?
  5. C

    Model M

    That is precisely what I was thinking. Several mothers ago I topped off the hydraulics but checking it was next on my list.
  6. C

    Model M

    The sheet metal has been off of it before. I was having new rims welded to the centers when this picture was taken. This is my shop.
  7. C

    Model M

    Thanks for the measurements. I just checked mine and it is the same as yours in reference to the full and add lines. My level after sitting is just above the last L in Full which is roughly the same distance as the add and full lines so I’m now thinking I am a quart over full and that could...
  8. C

    Model M

    All sarcasm aside, I should have said immediately “after I run it” and instead of “pushing” I should have said splashing which would have been a more accurate description. So, could my dipstick be too short and possibly not original to my tractor?
  9. C

    Model M

    Wouldn’t that show low when I check it at shut down?
  10. C

    Model M

    DIP STICK! Charles
  11. C

    Model M

    I have a 49 model M that is pushing oil out of the dipstick hole. I thought maybe the breather cap was clogged but it’s not and while it’s running there is very little blow by coming out. After I run it the oil is right on the full mark. Could I possibly have a short district? Thanks for any...
  12. C

    JD M fenders

    I need fenders for my M as well. Following this with interest.
  13. C

    M tractor and flail mower

    I didnt know that there was an accessory catalog. Point me in the right direction please.
  14. C

    M tractor and flail mower

    Thats what I was thinking.
  15. C

    M tractor and flail mower

    Please provide more information. What brand and model flail? Dont know yet. What is the manufacturer's minimum horsepower requirement? Dont know yet. Weight of the unit? Dont know yet. Do you already have a 3 point hitch? Yes. I generally associate hammers with rough, heavy cutting and brush...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top