(800) 853-2651
SHOP NOW

Recent content by CHILE43

Yesterday's Tractor Forums
  1. B

    New Farm

    Hope I m doing this right, lol. Bought a new home that has a 4 acre field. Field has been working every year, and this year I m hoping to grow pumpkins in it(central IL). Within my knowledge the land is okay but gets a little rocky. Previous crop was corn. I ve got a ford 9N to work with, only...
  2. M

    Toro General Tractor

    We're working on a Toro General Model B, Circa 1950(we think) for an FFA restoration project. Looking to see if there is there is a "go to source" for information on these - I've picked up bits and pieces across the internet - maybe that's the best that there is. Looking for a few parts and...
  3. kcm.MN

    Saturday "Extra" Pic

  4. T

    Nh 664 baler teeth

    Just seeing how you guys pevent breaking them I bale alot of road ditches and mole Hill areas and I tend to end up with small rocks in the band mounts underneath and it doesn't take long and you bust teeth when they wedge in the back has anyone done something as to not get rocks stuck in...
  5. M

    Steering column removal - Ford 600

    Our Ford 600 is in half right now as we prep to paint it....I have a question about the steering column and sheet metal that make up the dash panel. Can I remove that whole "piece" by the 4 bolts that hold this to the transmission housing? It looks like if I remove those four bolts and the...
  6. D

    Ford 600 fuel shutoff valve

    A young friend came to me about a leaking fuel shut off valve on his 600. He stated that it does not leak with the valve shut off, but leaks when the gas is turned on. Question-- is there an O ring he can replace by screwing out the shutoff shaft (with the screwdriver slot) or must he replace...
  7. rrlund

    Miss Michigan and me

    I finally got a copy of this picture. I've been looking for it for years. My aunt passed away and my cousin found a copy among her stuff. Of course I'm the good looking blonde cuss on the left who Miss Michigan can't take her eyes off of.
  8. D

    Wheels

    I have 2 Farmall 706. One has 38" wheels, the other has 34". Tires on both are junk. Which would be the best to keep & the other will go with junk tractor
  9. RBnSC

    Our Corn Crop

    Drove Dad to the farm and took a couple of pictures.This SC a few miles from where I 95 and I 26 intersect. Ron
  10. C

    power block pistons

    what are 6 inch power block pistons going for?
  11. C

    steering adjustment

    Install a pressure guage in the valve housing and tape the housing back and forth until you get the lowest pressure {90 to 110 psi}
  12. C

    oliver hg

    No.1 spark plug cable plugs in distributor cap in the upper right hand corner, cables 2-4-3 follow in clockwise order
  13. C

    6 to 12 volt conversion on hg crawler

    what type of bracket do you use to mount the alternator?
  14. C

    6 to 12 volt conversion on hg crawler

    does anyone out there make a 6 to 12 volt kit to convert an HG fron a 6 volt generator to a 12 volt single wire alternator?
  15. C

    gaskets

    Have had good luck with NAPA cheaper than Mother Deere
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top