(800) 853-2651
SHOP NOW

Recent content by Chris623

Yesterday's Tractor Forums
  1. C

    Innertube Problem/Question

    Well guys, thanks for your comments and suggestions. I've tried 3 auto parts stores and they didn't know what I was talking about when I mentioned longer valve cores. One was a NAPA parts store. The tube doesn't air well at all. Have to move the hose valve all around and only sometimes does...
  2. C

    Innertube Problem/Question

    Thanks, I thought of that. All the stems I have are labeled as short stems. Maybe I should go to the auto parts store and look for some labeled long. Thanks.
  3. C

    Innertube Problem/Question

    Don't know if this is the correct forum or not, but here goes. Needed a new innertube for one of the front tires on my Ford 8n and ordered one here from Yesterday's Tractors. Got it in the tire and aired it up................but my gauge wouldn't read it. It's a digital gauge. Reads every...
  4. C

    My first shot at rebuilding my 8n's hydraulic pump

    Basically what I did. Worked...............and got all my back pastures mowed. Front pastures tomorrow before everything gets too high to mow!
  5. C

    My first shot at rebuilding my 8n's hydraulic pump

    Got'er done. Works great. Made a lot of mistakes but learned a lot along the way. Thanks for all the comments and help.
  6. C

    My first shot at rebuilding my 8n's hydraulic pump

    Okie-Dokie..................got the new gaskets on the valve chambers and the pump installed. Next question: The control arm was very difficult to get into the hole in the rocker lever but I was able to force it in........it just didn't line up a slide in. (don't like forcing anything when...
  7. C

    My first shot at rebuilding my 8n's hydraulic pump

    These gaskets are what I'd call dark gray...................if they got wet I think they'd be black. They are very stiff. Ha-ha, now that I look at the envelopes they are sealed in they are marked CNH Industrial. Didn't catch that before just now. Guess they weren't "Ford Branded" like the...
  8. C

    My first shot at rebuilding my 8n's hydraulic pump

    My "Ford Branded" OEM gaskets came in today. Turns out the guy quoted me almost twice what I paid for them....................which was a real relief. They are only .020" thick though..........and the ones that are in the pump now are .019" thick. I'm going to pull the valve chambers off the...
  9. C

    My first shot at rebuilding my 8n's hydraulic pump

    Well, nobody can claim I'm not trying. :ROFLMAO: Spent the last 2 1/2 hour working on this. Got the drive tires jacked up 7 1/2" off the ground. Still can't get this pump to go forward and sit on that ledge..........or straddle that part it's supposed to go over. "So close yet so far"...
  10. C

    My first shot at rebuilding my 8n's hydraulic pump

    Just went out to my bench to take a chamber off and measure the gasket............................but turns out I didn't have to. A bit was extending out that was big enough to let me measure it with my dial caliper. It measured .019". But keep in mind that was a piece that wasn't being...
  11. C

    My first shot at rebuilding my 8n's hydraulic pump

    I tried to contact Ford New Holland and, of course, they are closed on Saturdays. I can't measure the gaskets I installed unless I disassemble the pump. But I did notice those gaskets were thinner than the rest of those in the packaged kit sent by Yesterday Tractors.
  12. C

    My first shot at rebuilding my 8n's hydraulic pump

    Okay, what is the "right size" ???
  13. C

    My first shot at rebuilding my 8n's hydraulic pump

    Thanks, Hobo, I followed that link last night just before I went to bed. I finally got what you were trying to tell me. Can you tell me what the measurement is that the chambers need to be apart? Or would installing a second set of the same thin gaskets solve the problem?
  14. C

    My first shot at rebuilding my 8n's hydraulic pump

    Don't know what you're talking about when you say "thin gasket problem". I purchased the gasket kit from Yesterday's Tractor. The pump goes up into the tractor so the chambers aren't keeping it from going inside the hole. They sure aren't hitting the sides of the opening when I raise the pump...
  15. C

    My first shot at rebuilding my 8n's hydraulic pump

    Thanks. That's what I figured out.............but I can't seem to get it to go up and in that way. ???? Just finished eating dinner. Will get back at it. Thanks again.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top