(800) 853-2651
SHOP NOW

Recent content by chrisfarmallf20

Yesterday's Tractor Forums
  1. C

    farmall governor spring question

    Thanks. I"d shoot you an email but you did not provide one. You can reach me at [email protected]. Thanks!
  2. C

    farmall governor spring question

    Thanks for the info but I checked out that website and neither of those part numbers is found. Please help!
  3. C

    farmall governor spring question

    Is this the spring I should be getting for my M and 400? I"ve read a lot on these forums about the 167 spring but have not had much success finding it...I think I have though in this link. I tried to reach out to ChadS, however, the number I saw in posts farther back doesn"t work. If anybody...
  4. C

    single acting cylinder help

    Not true. I removed the spacers on the cylinder and was able to push the ram back to the "down" position. It was hard the first couple of times but then it went easier...making me believe there may have been some trapped air in there. I checked the tops of the hydra-touch valves and they were...
  5. C

    single acting cylinder help

    I'll check the valve on the tractor. Thanks. I did try both outlets on the back of the tractor and I believe the one one the left is the proper one to use. also it is a new cylinder and it is a vented plug on the far end. I'm just wondering if it would be air bound. I'll remove the spacers to...
  6. C

    single acting cylinder help

    I"m probably just stupid asking this as I couldn"t figure out right away this afternoon but we just bought a new Bush hog for our farmall 400 and it has a single acting hydraulic cylinder on it. The cylinder had a number of spacers on it. We hooked it up and can tell the hose is moving from the...
  7. C

    tire pressure

    Fairly new to pulling. Have an M and 400 farmall that we took to a local pull a few weeks ago. Had a bit of a hard time "hooking up" to the ground and spun out a bit early. I"m thinking we had too much tire pressure but not sure if there is a general "sweet spot" tire pressure to start at and...
  8. C

    farmall m-450 hitch

    I"m in NJ but could pay for your shipping cost. You have a picture or any further information on exactly what it is/configured? Thanks
  9. C

    farmall m-450 hitch

    Not sure if original post made it but posting again...was curious if there is anybody out there fabricating hitches bolt-on for IHC tractors that would be adjustable for height etc...can't seem to find anybody out there and wanted to see if it is already available before going to a...
  10. C

    Farmall 400 Running Rough

    On very low idle, it seems to run quite smooth. When sitting but throttle opened-up...the motor runs extremely rough. When under load, however, it does even itself out a bit. I had the carb off and cleaned it up very well. No problems there. Getting fuel from the gas tank just fine as well...
  11. C

    farmall m carb freezing up

    Thanks for all the info. I'll try the re-adjustment and this past week has been extremely humid...I assume the moisture in the air drawn into the carb freezes up as the fuel atomizes. Hopefully lower humidity will help. It does have a gas manifold and I'll check the 'holes' another reply...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top