(800) 853-2651
SHOP NOW

Recent content by chuckj1954

Yesterday's Tractor Forums
  1. C

    timing on super h

    thanks Wayne, this is very descriptive and thank you. I'm imagining that, even before I follow your instructions in your first paragraph, I should have number 1 at tdc, which would have me on the pully mark to start, yes? sorry for the dumb question. thanks
  2. C

    charging a 6 volt

    I've run my battery way down. I have a six volt charger and put it on at the 2 amp setting. I am getting a reading up to about 67% charged and it seems to stop here with no further charging. The charger has a 15 and also 40 amp setting. Will I damage the battery if I go on up to the 15 amp...
  3. C

    timing on super h

    i have had big issues with my distributor. I made a terrible mistake, pulled the distributor without marking the housing and now have to time from scratch. I have a basic understanding and thought I could get close enough, taking #1 to tdc and then lining up the rotor with the number 1...
  4. C

    PTO seal replacement Super H

    thanks fellas. One more dumb question. Should I grease this thing before I put it in?
  5. C

    Super H carburetor

    I have a Super H and have the same problem. I've had the carb apart 7 times and this last time I thought, I finally got it. Here is how I tested it. I had the carb all back together, turning the carb over in my hands, upside down and right side up, I could hear the float move. then, I held...
  6. C

    PTO seal replacement Super H

    ok thanks. Should I go from the inside of the housing and push it all the way out to the rear back edge of the housing?
  7. C

    PTO seal replacement Super H

    I got my old seal out, driving it out with a round piece of oak almost the diameter of the housing. I drove it out from the outside in. I have the new seal, considerably thinner, which I understand is ok. My question is, when reinstalling the new seal, should I put it in from the outside in, or...
  8. C

    Replacing Super H PTO seal

    Lucas, I have a Super H, too. I just got the new seal for my PTO shaft. I haven't changed it yet but don't think it will be too difficult. Good advice in this thread.
  9. C

    Super H distributor

    I sent you an email. I'm very interested. thanks, Chuck
  10. C

    Super H distributor

    I'm still struggling to figure out the cam shaft in my distributor. I had posted the other day about it and the general concensus is that it is either bent or that the bushing is bad. Third possibility is that two lobes are slightly worn. Bushing seems tight. I'm down to bent or worn. I'll pose...
  11. C

    distributor cam Super H worn

    I'm going to try to remove mine this evening and see if the shaft is bent. I thought to gap the points on the lowest breaking lobe. The others would be opening more and past the .020 spec, but might work to make all cylinders fire. perplexing for sure
  12. C

    PTO seal for a Super H

    would you recommend two, or is one sufficient? By the way, you guys are amazing, I just got off the phone with my NAPA store up the street. He will have it sent from warehouse to this store by 11 am this morning. Thank you, all!
  13. C

    distributor cam Super H worn

    I did a little video on this. Don't know if you will be able to see much more, but I welcome views and suggestions Distributor Cam
  14. C

    I need a distributor hold down clamp (M/SM) IH distributor

    ha! amazing, I need one too. I have a super H and the inside bolt and bracket are missing. It has been that way for a very long time, never knew it wasn't there. I would buy one too
  15. C

    distributor cam Super H worn

    here's a picture
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top