(800) 853-2651
SHOP NOW

Recent content by Client

Yesterday's Tractor Forums
  1. C

    4020 loss of engine Power

    I got the IP to Richard Norman. If it's not one thing it's a dozen others. Today I removed the clutch access panel from the tractor belly and ball bearings started falling out. The bearing cage is completely separated. I know this means splitting the JD4020! I need to know the best place to buy...
  2. C

    4020 loss of engine Power

  3. C

    4020 loss of engine Power

    I'm waiting for Rich Norman, DeiselTech, to send instructions for shipment. I thank you for yours and others help. I could not have made this happen without the forum! All you guys are the best! Sincerely, Robert Reid in Arkansas
  4. C

    4020 loss of engine Power

    Some of the IP techs reference using a Bosch setup to run and analyze their rebuild. Are you familiar with such and if you recommend using a tech that uses this technology?
  5. C

    4020 loss of engine Power

    Are you aquatinted with Rich Norman DeiselTech?
  6. C

    4020 loss of engine Power

    Thanks to you gentlemen the tractor is in the barn, IP is removed, and now I'm sourcing a tech for exchange or rebuild. I have spoken with a Rich Norman, DeiselTech . Also, have talked with Badger Diesel and they use the EID one piece all metal weight cage which sounds like a acceptable upgrade...
  7. C

    4020 loss of engine Power

    How do I find Diesel Tech on this site?
  8. C

    4020 loss of engine Power

    I understand! Waiting until it warms up outside.
  9. C

    4020 loss of engine Power

    I got interrupted by my bride of 55 yrs. First thing Monday I plan to use your guidance and get it in the barn and get ready for the IP removal. All you gentlemen have made this a comfortable experience and I am grateful for everyone's help! A local friend of mine should know where to take the...
  10. C

    4020 loss of engine Power

  11. C

    4020 loss of engine Power

    It's about a thousand feet to the barn. Will that be okay if I loosely put the gasket and plate back on?
  12. C

    4020 loss of engine Power

    I removed IP window and she started right up. Jim MN says IP pump needs to be rebuilt. I need to know if I can drive it with the window off so I can get it out of the field and into the barn?
  13. C

    4020 loss of engine Power

    Followed the stated steps, tractor fired right up and throttle responsive as designed. Can I drive the tractor with the window off so I can get it out of the field to the barn? I'm going to need a step by step guide for IP removal. I did this once in 2007 and remember that the flywheel had to be...
  14. C

    4020 loss of engine Power

    Tractor now fails to start. It has been starting and running for 20 minutes or so then gradually quits. I was going to check the gas cap venting and rule that out. Next, I'm going to remove the IP timing window plate and check for debris and try starting with plate off. Finger's crossed!
  15. C

    4020 loss of engine Power

    Will check it out Sunday afternoon and let you know. Are you saying start the engine after removal of the cover and gasket or before removal?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top