(800) 853-2651
SHOP NOW

Recent content by cnc2000

Yesterday's Tractor Forums
  1. C

    Lift Arms

    Can anyone tell me why my MF 50 leaking oil at the top of the lift cover, it looks like it may be coming from the stand pipe, the lift arms appear to be working fine. I thought check if anyone could point me in the right direction before I started taking apart. any info would be appreciated.
  2. C

    Massey Furguson 50

    since the head gasket blew do you think I should pull the sleeves and clean them before I put the head back on. I put fresh antifreeze and water in it before I started it. Going out to drain it now and maybe pull the head later.
  3. C

    Massey Furguson 50

    What do you think about raising them up a bit and cleaning under the lip and sealing with green Loctite before torqueing it down. I have not pulled the head yet since the back fire , before I put it on the last time they appeared to be raised like the IT shop manual said.
  4. C

    Massey Furguson 50

    I had all new sleeves pressed in, new pistons, new grade 8 nuts, no over heating issues, the only thing that wasn't done is surface the head, machinist said it didn't need it and I did not re torque, I cleaned it real good, Im going to try it and see what happens. I ordered the gasket today...
  5. C

    Massey Furguson 50

    this is my first wet cylinder engine I've done cars and motor cycles and never had a problem. I am a little aggravated with it mostly about the parts it took yesterdays three tries to get me the gasket and 5 weeks of waiting for it. the first one they sent was bent across the first cylinder you...
  6. C

    Massey Furguson 50

    No but I will next time thanks
  7. C

    Massey Furguson 50

    I rebuilt my Z134 engine after about 8 hours on the engine it backfired a couple of times and that was it, the head gasket blew, antifreeze all over the pistons and cylinders. Cleaned everything up and replaced the gasket, torqued it down (had to use a wrench on the side nuts) I got it running...
  8. C

    MF 50

    I only turned it by hand and they still appear to be at the same height just above the block.
  9. C

    MF 50

    Thanks for input
  10. C

    MF 50

    that's what thought it was until the machinist said it was not, I don't think I will be sending him any business. I think I will use the green lock tight around the top edge to seal it when it goes back together and look for another machinist. Ill keep you posted.
  11. C

    MF 50

    This is a new rebuild, I should have mentioned it before.
  12. C

    MF 50

    The engine was cold with all new sleeves pistons, crank was turned, new crank and rod bearings, this is a Z134 gas engine. The machinist said it was a dry sleeve engine. I heard that you can use green lock tight to seal the top side of the sleeves. any info would be appreciated.
  13. C

    MF 50

    I thought I would that no water showed up in the oil.
  14. C

    MF 50

    I have a MF 50 do not know the year, I bought it in 1999 the engine had a stuck valve after I ran it for a while it loosened up and then it ran ok for the last 15 years. It only had approximately 75 pounds of compression so I decided to rebuild this past winter. It did okay after the rebuild for...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top