(800) 853-2651
SHOP NOW

Recent content by CT_Farmall

Yesterday's Tractor Forums
  1. C

    Farmall Cub Electrical

    Thanks John, I will get into it tonight. Will post results later. I don't think it is charging because at high rpm idle the needle of the ammeter is at dead center. Tim Tim
  2. C

    Farmall Cub Electrical

    u:ad08da47c8][i:ad08da47c8][/i:ad08da47c8][/u:ad08da47c8]
  3. C

    Farmall Cub Electrical

    I just pulled in a 1953 FCub that I was going through and getting in shape this evening. I noticed that this tractor has a 6V distributor ignition. As I was cleaning up the wiring on the battery and removing the corrosion I noticed that the negative was to ground and positive was to the...
  4. C

    JD LA Snowplow

    Was lucky enough to purchase an original JD LA snow plow. Picked it up this weekend but need some pictures as to how to hook it up. Anyone have any digitals of how to hook up the lifting strap to the front pivot. The installation instructions describe mounting the lifting strap but don't show...
  5. C

    Farmall A Temperature Gage

    Ok I snapped some pictures of my current set up. Step #1 Below Mounting Step #2 Fish Sensor Lead behind Fan and governor arm. How do you fix lead as to not get caught in governor arm or pulleys? Step #3 Connect sensor to return housing from block. How delicate is the sensor...
  6. C

    Farmall A Temperature Gage

    Vic, Can you scan in and email that to my address [email protected] Thanks, Tim
  7. C

    Farmall A Temperature Gage

    Here is a picture of my gage and lead. Somehow the lead doesn't look long enough to go from the top of the governor housing to the water elbow on the lower left of the tractor.
  8. C

    Farmall A Temperature Gage

    The tractor I have looks to be a distillate model but I don't have the separate gasoline tank. The carb was ID'd as a duel fuel when I rebuilt it(adjustable main jet) and the original hood had an extra hole for the gas tank cap. The lower coolant return housing off the engine is already...
  9. C

    Farmall A Temperature Gage

    I am piecing together a Farmall A 1941. I just purchased a temperature gage. It has the 2 hole bracket on it. Where does the gage mount on the sheet metal. Any pictures would help. Thanks, Tim
  10. C

    Farmall A Implement Parts - A60 Blade

    I am looking for the handle on the lift that connects to the rod and spring. It is riveted to the lever. The one that I have is about to break through the metal (all rotted). Case/IH calls it retired. P/N 25549B. Where can I find one.. Thanks CT
  11. C

    #51 Plow

    Thanks Bob, I have the parts and operations manuals but I didn't remember seeing any spec.'s in there. I need to figure out if I can get it home or get it hauled. Thanks Again,Tim
  12. C

    Farmall A Plow

    Good afternoon all... I have a guy that works here with me that is looking at replacing a moldboard on a Farmall A single bottom left and right plow. I believe he said he is missing the right hand moldboard. Does anyone know what part number this is and where he can find it. Thanks, Tim
  13. C

    Farmall A Zenith Carb Problem

    Well I went to work tonight and put the upper body in the Bridgeport. Found centerline of the hole and re-tapped the hole. The remaining material came out the bottom of the fuel inlet and all is well. It is for sure a special thread on the seat, I checked it on the comparator and it is not a...
  14. C

    Farmall A Zenith Carb Problem

    Tried that before I drilled it out with no luck.
  15. C

    Farmall A Zenith Carb Problem

    The major diameter of the new seat is .343. A far cry from the .375 of the 3/8-24. That is what is keeping me from running a 3/8-24 tap in there. Tim
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top