(800) 853-2651
SHOP NOW

Recent content by Curt Smith

Yesterday's Tractor Forums
  1. C

    high rpm massey 444

    Why would you turn a stock motor that hard? At the end of your hook it would be at like 1800 anyway. May be expensive 30 seconds sometime soon!!
  2. C

    Policing a farm stock class

    BuickAndDeere 5353M are correct. Hitch height (16-18?) and MPH (3 to 3 1/2) will level the field. Any HP above maintaining speed and spinning out at the end is not used. And a 12mph tractor will scar a 5mph tractor by 10feet every single time. It?s a weighted drag race. Physics. Law of motion.
  3. C

    Casey IL pull cancelled for today

    The pull for today in Casey IL has been CANCELED. The next pull will be June 9th at 1pm.
  4. C

    310 in Oliver 77

    You can run electric fan on front side to allow room for stock pump. I cut the shaft on pump off for more room. Cores are worthless. Spin on oil filter base is expensive but allow side shield to close. Single wire alternator is small and will fit easily. Most use 88 bell housing etc.
  5. C

    bolts for rear weights

    Drill your weights to 7/8. Use 3/4 all thread bolted tight to wheel. Measure for length. You will have no problem with three sets. We bolt on up to 6 sets. Email for more info if you like.
  6. C

    regrinding cam for oliver 88

    I have a new cam that ld sell. $200 plus core. Contact me about profile. 217-822-6199
  7. C

    hitches angle and thoughts why

    Angle makes no differece. Its how and where you bolt it up. Your 3rd bullet point is on the mark.
  8. C

    Front tires

    Using low profile motorcycle tires will drop you about 2 inches. You can mount them tubeless. Ive been running them for 20 years. USAP allows.
  9. C

    Boonville lN start time?

    Anyone know what time Boonville Indiana pull starts on 14th?
  10. C

    Is Cerro Gordo lL pull still on ?? June 18

    Is Cerro Gordo lL pull still on for today??
  11. C

    road sharpen tires

    Weight up the tractor. Find a steep paved hill and pull your truck up it a few times. Look at the bars. If you dont see fresh rubber all the way across the lug then let out 2lbs of air and repeat. Id start about 9lbs.
  12. C

    John Deere 60 weight

    You can make 5500 with the cast centers but you have to take off pto and 3pt and l changed powertol front end to an A with steel wheels.
  13. C

    hard blocking 88

    I am hard block to the top. I only cool the head. Electric fan and pump. Usually have to leave off a bit or lm forever getting to 140 , then it cools just fine. Call me if u want more info. Curt
  14. C

    Spark Plugs

    I would stay with the 386. But consider a .027 - .030 gap. I hav ran those plugs for years in Olivers.
  15. C

    Offset Grinding crankshaft

    HAPCO. Terre Haute IN. Just call them. SpeeDee delivery is cheap shipping.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top