-
C
Generac Guardian standby generator on sale
I have a relative who installs & repairs whole-house generators by Kohler and Generac. ....He has to attend factory service schools to maintain being a dealer. He tells me that the quality of Generac units has improved greatly over past years while the quality of Kohler has declined. I think... -
C
502 BBC heads question ?
According to this link, most 502's (1990 & later) came with cast-iron rectangular port heads. https://www.gmperformancemotor.com/parts/12562920.html Aluminum heads for the 502 are available in oval or rectangular ports. -
C
Puzzled by trailer lights not working
LED lights will not work on reverse polarity. ....Is it possible they are not wired correctly? I would suggest disconnecting the trailer from the truck and using a battery to connect to the LED wiring. ....If they don't light, try reversing the polarity. .....Most LED's are not damaged by... -
C
Air dryer for 150 CFM compressor
Don't know what your idea of "inexpensive" is. Here's one with 150 cfm rating for $89: https://www.tptools.com/3and4-InlineandModular-High-Capacity-Water-Separator,8789.html?b=d*8082 Other sizes also available from this supplier. -
C
The end of an era at Lincoln
My Lincoln tombstone is at least 71 years old. ....It is the 180 amp, AC only, model with the plug-in leads. ....Having copper windings, that welder is much heavier than the later models. I was tempted to buy the 225 AC/DC model when they were $99 but I never did. -
C
Winter arrived last night
How does that chuck mount? ....Threaded spindle? .....Cam lock? -
C
tabletop lathes
You didn't specify if you're looking for a wood-working lathe or a metal-working lathe. -
C
Got me a metal disintegrator...
Brain fart, here! You need a step-up transformer from 220v single phase to 440v single phase NOT a step-down as I linked to above. -
C
Off brand tools that are actually pretty good
:thankyou:Truer words have never been spoken! An analogy I once heard: "You can buy the most expensive golf clubs but that doesn't mean you will play like Tiger Woods!" -
C
Calculating Hydraulic Pump GPM On A Log Splitter
You can work backwards to get the flow rate of the existing pump using the inside diameter of the cylinder, the stroke length, and the time it takes the cylinder to extend fully (with no load). An 8hp engine should drive an 11gpm two-stage pump. ....Higher gpm pumps will require more hp to... -
C
Newbie here, struggling with my MF 12G
Attached is a Tecumseh Manual for 8 hp to 18 hp Cast-iron Engines. Your HH120 is covered by this manual. Scroll down to Section 8 (page 45) for info on testing the solid-state ignition. New Tecumseh solid-state components have been unavailable for many years. ....Expensive used parts are... -
C
harbor freight 20 lb. sand blaster - looking for tips
Pardon my ignorance, but what is an offset pit? You may become frustrated filling your 20 pound blaster quite often. -
C
3 wheeled reel mower, Kohler K161t engine....any clues as to what is is?
The Kohler Serial number indicates the K161T engine was built in 1977. Assuming the engine is original, the mower was probably built in 1977 or 1978. If you can find a Toro id on the mower, I may have a manual for that mower.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy