-
DDanielW replied to the thread Bush Hog Disc.Very much dependent on the soil type. But a fair bitof HP to pull it effectively if running full depth. Offset discs pull way harder...
-
DDanielW replied to the thread 8N bogs down.The missing port mentioned above is definitely a common problem with new/aftermarket carbs. And can cause exactly the type of issues you...
-
DDanielW replied to the thread Shuttle Shift Tractors ????.I think Vito's response pretty much nails it: It boils down to how much you want to spend. I'm certainly no expert, but I've baled (or...
-
D466 would be the next 4 ft wide model. I highly recommend skipping that model especially if it has wide pickup & move up to 467/567 or...
-
DDanielW replied to the thread Anyone re-skin a 1950's shop?.If you get snow loads, I'd want new steel on the roof. Especially for a lower slope like that. Old steel with a bit of surface rust...
-
DDanielW replied to the thread Anyone re-skin a 1950's shop?.I thought the same thing. 2x6's on their flats at what looks like 24" spacing and 8'-10' truss centres. Don't think I'd want to try that...
-
DDanielW reacted to GBman's post in the thread American Bosch PSB6A-75C-3411A Injection pump, I know they're a pain with
Like.
Hi Daniel and John: I replaced the seal on pump drive and it seems to work very well now! I have new question that I will make a new... -
DDanielW replied to the thread 851 auto tie. New Holland.I feel the same way personally, but I also think it's dependent on your feeding methods and climate. I always pull the twine off while...
-
DDanielW replied to the thread Anyone re-skin a 1950's shop?.I'd be looking around at other quotes, and maybe start with just the roof. $60k sounds stupidly high. There are some cheaper options you...
-
DDanielW replied to the thread C 28 mower.Rick is correct. I have two C28's and one C32 (the trail version of the same mower) and they use C-section belts. Mind you, on one of...
-
DNet wrap makes for a lot faster baling and it does help protect the bale if you store outside, but other than that it is awful to deal...
-
DDanielW replied to the thread Ford 8N replacement gas tank cap?.Had the same thing with a replacement cap on our 2N. Not sure why, but two different replacement caps were loose and wobbly. Turned out...
-
DMy biggest gripe about cables is the clamp-on replacement ends. They often corrode where they clamp on & should be used in an emergency...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy