Recent content by dave

  1. D

    McCormick International 43 Baler

    The little lock part that holds the tongue down on the ball gets beat to trash quick on the cheap couplers.Then to add insult to injury you will find out it has been bent useless by the baler jumping off in the worst spot.Try to find a solid clasp or old cast u-haul type.Learned the hard...
  2. D

    OT computor help from the experts

    not sure of the system and I am no expert,however it might be the settings on the taskbar has been changed,rt click the bar, look for properties or settings,then look for a box to check called "keep the taskbar on top of other windows" and make sure it is checked in the box,and also make sure...
  3. D

    My turn with truck question

    I"m not a expert, but there is a oil bypass valve,I think its in the adapter that the filter screws on.last I recall theres was a plug in this.anyway if this spring or stopper valve gets weak, or stuck it bypasses the filter and dumps the oil straight to the oil pan.Its a safety thing in case...
  4. D

    OT: building project (with pictures)

    very nice.thanks for sharing.
  5. D

    Thanks for Tractor Talk

    I agree,I don"t post alot but I am always reading.fine site, fine folks.
  6. D

    And It gets worse for smokers

    Its funny a discussion about clean air on a tractor site,where smoke belching diesels are the norm. I also know before you say anything about health costs of smoking,its usually known as a pre-existing condition and insurance will not pay,applies to back failures too.and if you get diesel smoke...
  7. D

    Jerry Rigged

    count your blessings you have such a nice machine to work with.I think it looks fine. Just a little paint is all it needs.Nice weld too,what did you use to get a bead like that?
  8. D

    Twisted Metal - I Made It

    hang in there,glad your ok.
  9. D

    B+S Intek, hard to crank / conks out/ very hard to crank

    seen several of the engines with the .5 on the end have the valve seat come apart from the block,causing the valve to not be able to open.tried repairing a couple,by staking the seat in the engine. one lasted a day, another lasted a year,before the same thing.
  10. D

    Farmall H miss and throttle issue

    I had been getting bad fuel locally in sw virginia.I had many machines acting bad and idling funny.I did all sorts of things until my friend told me to add some octane booster.It worked on everything,and I am changing gas stations.I thought I would add this as it baffled me for a few weeks.I...
  11. D

    farmall B-negative battery terminal warm-wont crank

    might be the starter stuck,in a bind.My H does that once every 3 or 4 years during a rain or snow it seems.fix for mine is usually loosen starter,until it is almost off,shake it some, hit starter to make sure spins,slide back together and tighten bolts. the real fix is to replace some parts but...
  12. D

    True Value Lawn Chief 44CA-L Parts

    found this might help, i would copy asap http://www.goots.net/lawnchief440
  13. D

    OT old Snapper Series 6 repowering

    the big disk on the engine shaft is likely to be a pain,always was for me.Also, you might want to look up parts for the tecumseh,as they are no longer making any.I am searching for a carb for a 16 ohc and they seem to be getting scarce.my advice is to repower with a briggs, if you can.Good...
  14. D

    Odd problem with a B/S engine

    sounds like a sunk float or something in the needle valve/float area stopping it from closing off the fuel.
  15. D

    Farmall C oil pressure

    If it is that small automotive type,there are kits available in most automotive parts houses for replacing the lines in cars.Even if different take the remains to a good helpful local auto parts guy.They should have what you need in stock.
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top