-
D
Hydaulics (with loader)
The dipstick looked good, so I will take the cover off and peek inside. -
D
Hydaulics (with loader)
Here is a photo of the current hyd pump (seems to be there still which is good). Is everything mentioned internal to the pump, I don't see any drive that would operate the proof meter. -
D
Hydaulics (with loader)
Thanks, I have already purchased the Operators' Manual (and was surprised with some of the info provided). The Service Manual is definitely needed it seems. She also over heated the other day, so sounds like I need to replace the thermostat as well. -
D
Hydaulics (with loader)
So what the plan of attach, confirm the original pump off the rear of engine/flywheel is still there... and 2) remove the cover to take a look inside ? Which cover should be removed, the one just aft of the gear shift lever? Under the seat? -
D
Hydaulics (with loader)
I was finally able to get some more photos, it seems the pump has been re-routed to directly power the lift, bypassing the feed back into the housing which operates the 3 pt... If this is the case, how do I get the 3pt up and running again? Can I install a manifold at the pump to feed both... -
D
Hydaulics (with loader)
Thanks for the response, but no clue what that means...is the 3-point not getting an pressure from the pump? Trying figure out how to get the 3-point working. -
D
Hydaulics (with loader)
The 600 I just picked up has a front loader on it, I have not seen any pictures in my researching of such a setup so was wondering if it is an aftermarket install? The reason I ask, the hydraulics for the bucket work, but the Touch Control Lever does absolutely nothing for the 3-point. Could... -
D
Ford 600 Alternator Question
Thanks all, I brought it in to a local Automotive Electrical shop...said it was a Mitsubishi. The 3-wire plug should be going to an external voltage regulator (which I'm pretty sure doesn't exist). The brushes were sticky and the bearing was shot. Ended up just buying a new 12V kit from... -
D
Ford 600 Alternator Question
Thanks Bob, diagram is helpful...so my options: Find a new harness for this? I could find a new plug and try and re-pin the existing wiring Get a whole new setup? -
D
Alternator Harness (plug)
It seems the taped single wire is the old wire to the generator? The frayed wire is right at the connector, it could probably be fixed by re-pinning it, but I would rather get everything set properly with new wiring, I always hate relying on previous owners setups... One wire definitely goes...- Dcroteau
- Post #1
- Forum: Tractor & Farm Talk
-
D
Ford 600 Alternator Question
The taped plug seems to be the old single wire for the generator? -
D
Ford 600 Alternator Question
The taped plug seems to be the old single wire for the generator? -
D
Alternator Harness (plug)
- Dcroteau
- Post #1
- Forum: Tractor & Farm Talk
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy