-
D
installing grease zerk for rear axel bearing
I have been tapping and installing grease zerks on the ford rear axle for many years, JD & IH did it so why not Ford don't think it could hurt a bearing to grease it (THIS WILL STIR THINGS UP wink wink) -
D
Half tracks
Got a good set of tracks, very nice (tracks only) rest was home made, southern Minnesota -
D
Interesting Jubilee
It works like a racket and you can set it to go one notch-two notch-up to four, the more notches the faster it moves- DEAN C
- Post #1
- Forum: Ford 9N, 2N & 8N
-
D
Interesting Jubilee
The trencher was built by Blackhawk it is driven with chains to the rear wheels with a big sprocket attached to the rim, speed is controlled by a racket system, it will dig 6ft deep the trencher is driven with a Ford pulley gear box with double V belts- DEAN C
- Post #1
- Forum: Ford 9N, 2N & 8N
-
D
Valve job on an 49 8n
Years ago we hand lapped valves all the time worked very well, I still have the tools to do it, had to use them two years ago on a old combine motor because didn't have room to work with the other tools it took time but it worked out well- DEAN C
- Post #1
- Forum: Ford 9N, 2N & 8N
-
D
Questions about my John Deere G project
My stuck at .008 went to .015 all worked fine---.008 mite work if you just drive around the yard with it.- DEAN C
- Post #1
- Forum: John Deere
-
D
Ford Industrial 1.6L
google northern power products Eagen MN Very good people to work with -
D
Wheel spacers
The red ones are for the 960 with mounted corn picker to get more space between the picker and the tire -
D
1954 Jubilee Oil
there are holes in the cam that must line up to get oil up there--as the engine turns over the oil goes through the holes--it controls the oil flow to the top--turn motor by hand while running the drill you will get oil -
D
Fried 172 Ford diesel ???
JUST A GOOD OLD ENGINE--Starts good--Good oil pressure--Plowed with it last fall pulls good--I have had it forever never used any oil About 17 miles south west of Mankato--$900.00 -
D
Fried 172 Ford diesel ???
I have 172 diesel motor in 981 tractor with a bad trans I would sell==can here it run==in south central Minn -
D
Pie weights
I have bought the adapter nuts from SPAREX in the past for $3.50
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy