-
D
1800 hydraulic pump replacement
What is the best route to take on this ordeal- deere hound
- Post #1
- Forum: Oliver, Cletrac, Co-op and Cockshutt
-
D
1800 hydraulic pump replacement
Checkerboard A series- deere hound
- Post #1
- Forum: Oliver, Cletrac, Co-op and Cockshutt
-
D
1800 hydraulic pump replacement
New to Oliver always liked the look..looking at an 1800 with a bad hydraulic pump what is the cost of pump and what does it all involve with replacing it?- deere hound
- Thread
- Replies: 6
- Forum: Oliver, Cletrac, Co-op and Cockshutt
-
D
7000
A 7000 showed up on radar for sale so close I could drive it home..good rubber,good sheetmetal,seems solid a few minor leaks,it has the 2 shift loadmonitor tranny on it..I gotta shoot a price..looking for a fair ball park offer...new to ford here..how does 2500 to 3000 sound? I'm OK with...- deere hound
- Thread
- Replies: 11
- Forum: Ford
-
D
Did I just blow a gasket?
Yes you did it's better to blow that one than wreck something else..on that note tighten it more..that may help..- deere hound
- Post #1
- Forum: John Deere
-
D
R pto delete
Was an R ever offered with a factory delete?..or an aftermarket delete plate?- deere hound
- Thread
- Replies: 3
- Forum: John Deere
-
D
730 std vs 720 std
Looking for opinions on the value of the 720 vs 730- deere hound
- Thread
- Replies: 7
- Forum: John Deere
-
D
5010 with 5020 engine
Looking at a 5010 it has a 5020 engine in..it was installed over 40 years ago by a jd dealer..Will this hurt resale from a collectors point of view?- deere hound
- Thread
- Replies: 8
- Forum: John Deere
-
D
1568 IH or JD 4630
Which is a better tractor? Red vs Green.- deere hound
- Thread
- Replies: 18
- Forum: Tractor & Farm Talk
-
D
650 IH Diesel
Thanks for the info...I think I'll pass on that 650...- deere hound
- Post #1
- Forum: Farmall, International & McCormick
-
D
650 IH Diesel
I have a few questions about a 650..It has a miss and smokes (not black)antifreeze is up to the top in the radiator.Other than the injectors what other problems may exist?..I looked at the tractor and tie rod is very close to the oil pan(1/8"away)is that normal or something bent..How difficult...- deere hound
- Thread
- Replies: 3
- Forum: Farmall, International & McCormick
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy