-
D
Ford 2000 three point will not lift
I have a Ford 2000. It is the three cyl. diesel. The lift was working when I last used it about a month ago. Now it will not lift. When you first start it it will lift about 2 inches then stop. When you shut it down it lifts an additional inch or so while shutting down. Then when you restart it... -
D
Ford 2000 rear axle outer seal
Hand pack it with grease. That seems to be kind of a Rube Goldburg kind of thing. There is no way to easily regrease it. You have to cut off the collar holding it in place.I then had to built a fixture to hold it to press off the collar. Then heat up a new collar to get it on. You would think... -
D
Ford 2000 rear axle outer seal
Thanks but I think I figured it out and ordered a couple off Ebay. Let me ask a dumb question. How does the bearing get oil when there is a seal on both sides of it? -
D
Ford 2000 rear axle outer seal
Serial number is 6-F-23-B I am having trouble finding the part number for it. The seal is 3.5" OD. 2.5" ID. and .5" in width. Thanks -
D
Ford 2000 injector pump
Got it started. Had not got it primed enough. Thanks for the help. -
D
Ford 2000 injector pump
It ran before I took it of. It had numerous leaks on the pump. Bought a kit and put new crush washers and gaskets and a new o ring type seal on the back plate. Put it back on the tractor and now can't get it to start. I lined up the slot in the gear to the pump. Does not seem to be getting a lot... -
D
Ford 2000 injector pump
The pump was leaking. Removed it and put new seals without disassembling the pump.Reinstalled and now cannot get the tractor to start. Does the pump only go in one way? As long as the pump and gear indentation line up it is good? Or does pump need to be turned 360 or more? Also how to remove... -
D
450-C master pin
Thanks Roy, the dozer is still running good after you told me about installing a new clutch control rod after I had tried to repair the worn out one, Donald- Don k
- Post #1
- Forum: Crawlers, Loaders, Dozers and Backhoes
-
D
450-C master pin
What is the difference in diameter of a standard as opposed to a oversize master pin? There are the 2 in the parts book. My pin is kinda loose and I was wondering if it is possible to drive the oversize in or you had to ream? Thanks, Donald- Don k
- Thread
- Replies: 2
- Forum: Crawlers, Loaders, Dozers and Backhoes
-
D
Hyd. cylinder repair kit
Ordered a repair kit from MINNPARR. We shall see.- Don k
- Post #1
- Forum: Allis-Chalmers
-
D
Hyd. cylinder repair kit
Are there repair kits available for the Hyd. cylinders that lift the blade on a Model D grader?- Don k
- Thread
- Replies: 2
- Forum: Allis-Chalmers
-
D
Model d hydralic pump
Thanks, a little pricey. Maybe look at a different pump that has about the same values make some brackets to mount it.- Don k
- Post #1
- Forum: Allis-Chalmers
-
D
Model d hydralic pump
What kind of hydralic pump and what was its output on a Model d grader.I think it is a 1957 model.- Don k
- Thread
- Replies: 5
- Forum: Allis-Chalmers
-
D
Model d grader
Does anyone make bushings for the front end, not the steering box?- Don k
- Thread
- Replies: 1
- Forum: Allis-Chalmers
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy