(800) 853-2651
SHOP NOW

Recent content by Donz

Yesterday's Tractor Forums
  1. D

    h3 Allis chalmers and ac 400 winch

    Hi troy25, Sorry I can't help with the winch or the reverser. That is the only thing I haven't touched on my H3. The engine is very similar to the Allis D15 tractor basically the only difference is the fuel pump, the tractor was gravity where the dozer had a mechanical fuel pump. Most switch...
  2. D

    HD3 Allis track release lock

    Loosen the two I think 9/16" bolts on the plate by the 1 1/2" hex rod one is above and one is below the hex coming from the tension spring. They are just behind the front idler yoke. They don't need to come out but they do need to be loose which can be a bugger if all rusted up. Then just...
  3. D

    Allis HD-3 steering clutch

    Sorry JK-NY I should have read all your post. I see you know of the steering clutch adjustment bolt. The steering lever should be adjusted to 1 1/2" - 1 3/4" from the rim of the tank adjust by the setscrew at the bottom of the lever. Then the clutch should have 3 1/2" of free movement measured...
  4. D

    Allis HD-3 steering clutch

    JK-NY if you look at the side of the machine at the rear final drive just in front of the rear sprocket and at about 11 o'clock you'll see a roughly 1 1/2" nut with a 1" bolt with no head it has a hole in it that is your clutch adjustment. Loosen the nut which can be a bear, turn the bolt using...
  5. D

    H-3 Allis

    Unless they changed the motor it is only around 43HP if it has the 166cid which was after mid 1965 if it has the earlier pre 1965 enegine it is 149cid its only 39 HP I believe. I think the diesel was 41HP. Also if the idlers and rails have been welded up the under carriage has alot of wear in...
  6. D

    adjusting H4 Allis tracks

    Pinball you are correct, loosen the two bolt and it should turn. You don't even need to take the bolts out from what I remember they just need to be loose. That small plate needs to be free as well. My guess is the threads in the yoke are rusted up. Keep spraying them down, you might even...
  7. D

    Storm damage pics

    Thank you all for your reply’s that makes since, I could see the spark thing with the old steamers. The belt thing now makes since as well so thank you again, Don
  8. D

    Storm damage pics

    Hi Jon, Not being a farmer or even owning a tractor I just love this site I do own a H3 Allis Crawler but I have a couple question for you folks. First what do you do with a mess like that, plow it under or try and salvage what you can? Second question when you see them threshing and they have...
  9. D

    430 Power Steering Pump

    Hi Guys, I have a good friend that is looking for a power steering pump for his 430 he believes it is a 1963. The serial number on the tag is 440 (8221450). The numbers on the pump are G-45292 and right below that it has GCCT 5645 from John S Barnes Co. Do any of you guys know where he could...
  10. D

    Tom Arnold 446

    Tom, thank you again I"m not sure why the pictures came out so bad. But I"ll follow your suggestion and pass. I"m glad I ask the questions. Thanks again for all your wisedom. Don
  11. D

    Tom Arnold 446

    First thank you for your insite on the mower. Here are a few picutres Tom.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top