(800) 853-2651
SHOP NOW

Recent content by DouginOlympia

Yesterday's Tractor Forums
  1. D

    Rotary Mower Advice Needed

    (reply to post at 15:25:50 04/16/21) I've watched some youtube videos that talk about brush hogs and what to look for, how to use them, etc. I think one of the best youtubers out there talking about tractors is "Tractor Mike". He's got a video where he talks about what to look for when...
  2. D

    International 424 - Where to connect the temp guage

    (reply to post at 20:09:01 04/15/21)
  3. D

    farmall 460 gas alternator conversion

    I thought this guy's youtube explanation of how to wire the alternator was really simple to follow. I used it for my diesel 424. https://www.youtube.com/watch?v=QVUL0S704AE
  4. D

    International 424 - Where to connect the temp guage

    photo
  5. D

    International 424 - Where to connect the temp guage

    for some reason I can't seem to upload a photo. I've resized it downward but when I try to upload it I get a message that says I've used words that are forbidden. My message didn't contain any words, just the picture (named block heater.jpg)... Kinda confusing.
  6. D

    International 424 - Where to connect the temp guage

    Well I took a look at that space between injectors 2 and 3. Someone at some time installed a passive block heater using this location as the highest point. I've used this inline heater and it works really well so I'm not going to just remove it. I'll have to decide whether its worth it to...
  7. D

    International 424 - Where to connect the temp guage

    Thanks for the help. I'll have to go with a new unit but at least I know where to attach the source end of the guage now. Doug
  8. D

    International 424 - Where to connect the temp guage

    OK, duh. Capillary tube. I haven't seen anything that looks like a capillary tube nor where it would connect to the block. A picture would be great if you can get one. Sounds like maybe I have to go with a new guage and capillary tube. Having some direction about where it may connect would...
  9. D

    International 424 - Where to connect the temp guage

    On my diesel 1965 International 424 with the BD154 engine, I'm trying to figure out where the temp guage on the dash is supposed to get it's signal. I've got the parts manual that shows all the wiring but it doesn't seem to show any wire that goes to a temperature sensing device on the block or...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top