(800) 853-2651
SHOP NOW

Recent content by Duetz Fan

Yesterday's Tractor Forums
  1. D

    #%^€¥! Hydravac..probably..

    That was one of my thoughts but it turns out the Hydravac generates incredable pressure and volume of brake fluid movement.. Short of spending a ton of money on new wheel cylinders and so on fixing the hydravac is the only viable option...
  2. D

    #%^€¥! Hydravac..probably..

    I think the master cylinder is good. I could plug the port to prove the theory but then where did the 2quarts of brake fluid go other than into the hydrvac in places it shouldn'd be? I look to get away from the hydrovac cause all I know about them is they fail. Finding a replacement hydrovac...
  3. D

    #%^€¥! Hydravac..probably..

    Over the years (2-3 decades ago) if you were working on a heavy truck with juice brakes and the brakes were doing funny things and you couldn"t figure it out, you replaced the hydrovac and the issue usually went away.. Thankfully Hydrovacs are a thing of the past. Unfortunately so are...
  4. D

    MF 1045 Glowv Plug Time?

    I'm looking for a manual but in the meantime, winters comming on.. Anybody know the number of seconds to cycle/warm the glow plugs?
  5. D

    MF 1045 3 Point Linkage Measurements

    I bought a MF1045 4x4 Loader Tractor. I'm suspect in it's previous life it had a frame mounted backhoe that would normally require removal of the vertical and lower 3 point linkages. Now just a loader tractor with 3 point hitch, the hitch lower link drawbars don't seem to have enough lift. When...
  6. D

    MF 200 Track Master link

    Track ON & properly adjusted. Not ( Trying to ) removing the master link was a good idea. The track had come off at the sprocket/trying to put an unbroken chain back on at the sprocket was not my best idea albeit it looked easier with the chain still in place on the front of the machine...
  7. D

    MF 200 Track Master link

    First, THANKS GUYS!!!! OK, one should always consider heavily the advise of those who have done it before... Currently I can lift the machine. I have the front idler retracted ( this is a small machine kinda like a John Deere 1010 & short track with decent pins may be whats making it so tough?)...
  8. D

    MF 200 Track Master link

    Well, I let the tracks get too loose & one came off. My Bad... I've located the master link pin / the ONE with the dimple... The question is, do you drive the pin out from the front/outside of the machine as your looking at the machine from the side or the rear/inside between the tracks or does...
  9. D

    Case 580C Starting

    I thought about the dry rings thing... Then I got into a few dat stretch of starting it daily. Same thing & when she fire a VERY small puff of black & then cear exhaust/no blue smoke. No blow by.... She runs too well to be rings...at least thats my thoughts without compression testing.. I'm...
  10. D

    Case 580C Starting

    This message is a reply to an archived post by Duetz Fan on January 05, 2012 at 03:56:08. The original subject was "Case 580 Starting". Well, Electrically everything checks out. Still starts hard but I have found something I find VERY interesting and I have yet to find an explaination. I can...
  11. D

    What other Wheels Fit a 135?

    Mine does not have a 4th gear... Pretty much everything but the front axel is the same as the 135... But thanks for the thought!
  12. D

    What other Wheels Fit a 135?

    Oh, sorry, yup its the one in Williamstown....
  13. D

    What other Wheels Fit a 135?

    I'm sitting on a sure thing mechanically but due to it's width it'll never get inside.. I either trade it or sell it or find another set of tires/wheels. It's too good running/operating to leave setting outside to run an hour or so a year yorke raking my driveway while the elements eat it up...
  14. D

    What other Wheels Fit a 135?

    I have a great running MF2135 Turfmaster Lowboy. Tractor other than needing a distributor cap runs/operates flawless. It stays outside cause it's so wide it takes up a stall and a half. I should keep the sure thing rather than sell/trade for another tractor sooo.. I'm looking for a set of...
  15. D

    Case 580 Starting

    True, $15+ or - spent would not change anyones lifestyle. I was in a NAPA a few days ago to stock up on oil filters. I prefer NAPA/WIX oil filters.. They have metal anti flowback valves/disks. Fram who has the best advertising campaign in the industry and likely the worst filters/some kind of...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top