(800) 853-2651
SHOP NOW

Recent content by Duvie

Yesterday's Tractor Forums
  1. D

    Another glow plug question B414

    That style glow plugs indicator seems to work with the 12 volt glow plugs that I installed. Takes about 10 seconds to glow and the machine starts up instantly! Prior to that she was almost impossible to start below 75 degrees. The 12 volt glow plugs were definitely the correct way to go.
  2. D

    Another glow plug question B414

    Just decided to go with the newer 12 volt style heaters. Remembered using my dad’s Massy 65 as a kid with the pepper pot and was trying to keep it on this machine. Machine will probably be much better starting with the 12v anyway.
  3. D

    Another glow plug question B414

    Digital meter doesn’t settle down quick enough to get a good reading before indicator gets too hot (also resistance is changing rapidly with the fast heating). I might have an analog meter at work I can borrow and try later in the week. Instance where newer isn’t necessarily better!
  4. D

    Another glow plug question B414

    Just purchased a B414 and all the wiring for the glow plugs was tore apart and Jerry rigged with bare wires and alligator clips! Ordered a new glow plug resistor/indicator that is supposed to fit a B414 and replace part number 3042230R91. Used a push button foot type switch for a ford to...
  5. D

    Running chipper with hydraulic feed on INTERNATIONAL B414

    Thanks JimB2!
  6. D

    Running chipper with hydraulic feed on INTERNATIONAL B414

    Just looked at my other B414 and the loader valve does have a relief as can be seen on the left side of the valve. This machine has a lot of blow by and is really hard to start. Looks like I may be doing new sleeves and such. She is plumed the same way the other machine is plumbed.
  7. D

    Running chipper with hydraulic feed on INTERNATIONAL B414

    JimB2, I am in the northeast USA and I do not see any sign of a pressure release on the loader valve or chipper.
  8. D

    Running chipper with hydraulic feed on INTERNATIONAL B414

    Jimb2, yes, I stated that in the first sentence of the post…..lol. I would appreciate some help on how to tie it in. The chipper connected to my John Deere’s power beyond so that makes it an open center type attachment if I understand correctly. The pump pressure line on the B414 goes to the...
  9. D

    Running chipper with hydraulic feed on INTERNATIONAL B414

    I have run the chipper on my JD 4100 that has a similar hydraulic flow rate to the B414 so I am not concerned about the flow rate. The hydraulics only drive the feed for the chipper, the pto does all the real work. Just looking for the best way to plumb it.
  10. D

    Running chipper with hydraulic feed on INTERNATIONAL B414

    I am looking to add hydraulics to run hydraulic feed on pto chipper. Machine used to have a loader and still has loader valves (see pictures). Pressure from hydraulic pump goes to top of loader valves assembly and exits at the bottom of the valves through a quick disconnect, then goes to the...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top