(800) 853-2651
SHOP NOW

Recent content by dwaldro

Yesterday's Tractor Forums
  1. D

    International Harvester Cultivator parts for Super A's

    In South Mississippi
  2. D

    International Harvester Cultivator parts for Super A's

    Anyone know a source for the "crosses" that go into the feet? Its the part that the bolt screws through that allows you to adjust the plow point. I don't know the real name but have always heard them referred to as the "cross". I'm needing some bad. thanks
  3. D

    CHOICE OF PAINT

    I have purchased paint and primer from them. Good product and good folks to deal with. Their Oxystick Epoxy Primer is awesome.
  4. D

    6ft rotary cutter with a TO35

    Found a deal on a 6ft rotary cutter. Thought I'd try it behind my 55 model TO35 when I get it all back together. Think the little tractor will handle it ok? I have a 5 foot that I've got to re-build but thought I'd hang on to this six foot and give it a try. Mainly will be clipping around the...
  5. D

    JD 3 bottom plow restoration

    Check out OxyStyx epoxy primer. It sprays well and has worked well for me. Get it from an outfit called the coatingstore.com. I use every way possible to get the rust off... wire brushing with 4 inch grinder/brush, scale gun and even electrolysis on some parts. Get it clean, clean.
  6. D

    12v wiring harness for TO35 with generator

    d I was scratching my head too like you and Steve but since this is one I plan to pass on to the grandkids, I thought I'd do it right. The suppliers will offer a harness but in the same add say "6v only" so...I was concerned about buying one that said for 6v only. Thanks to all for the advice.
  7. D

    12v wiring harness for TO35 with generator

    Anybody out there have a suggestion for a source? Looking for a wiring harness for a 55 model TO35 with 12v generator system. Serial #165393. Find plenty for 6 volt but trouble finding one for a 12 volt system and don't want to have to make one. Thanks, dwaldro
  8. D

    IH Red paint brands

    Check out this supplier. Thecoatingstore.com. The epoxy primer and paint they sell is awsome and it's a heck of a lot cheaper than the "big name" paints. This outfit does all of its marketing via the net so...they can sell quality products at a reasonable cost.
  9. D

    Headlights and work light for TO35

    hanks "Crazy in VT". That info from that link explained everything
  10. D

    Headlights and work light for TO35

    Trying to buy some 12v lights for my 55 model TO35 restoration. I dont think I can salvage mine. Is the 5 3/4 inch light the correct size and did the original have "TractoLight" stamped on the lights?
  11. D

    Re: MRS Tractor Mississippi Road Service Looking f

    his won't help you in searching for parts but just a little info here. My uncle worked for MRS Tractor. They were located in Flora, MS which is about 20 miles north of Jackson MS. I thought they closed down that plant in the early to mid 70's but I could be mistaken. I've never seen one of their...
  12. D

    trans/hyd oil again

    ey Steve. I had the same question about mine and I used the GL1 from Napa. I was told the reason the GL1 is to be used is due to the sulfur in new oils/fluids. I think it took 8 gallons.
  13. D

    Finding PROPER color paint for my 55 TO35

    South MS. Ordered some rattle can paint from a vendor off of this site just to see if the color was right. Plan was to match it to a good automotive type paint. It was way to dark. There is a Sherwin Williams paint store about 70 miles up the road so...I may have to give that a try.
  14. D

    Finding PROPER color paint for my 55 TO35

    Never realized how difficult it would be trying to get the CORRECT color of gray and metallic green for my 55 Ferguson TO35. Lots of paint out there but I'll be danged if I can find one in my area that is the correct gray or green. I've got the paint color numbers from FENA and still can't seem...
  15. D

    Rust stopper/Primer

    As soon as I wash the metal to get the phosphoric acid off, I will have flash rust. Very high humidity here. I guess I will go over the washed metal with some 600 wet or dry and then wipe it down and try to prime as soon as I can after doing that. [i:f0d57b5b1f]It makes me ask the question...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top